Swap meet...

[thomas1]

I knew that but couldn't resist poking a little fun at the Boy Wonder.

Just reinforcing the point.

 

[MS460WOODCHUCK]

My wood cutting buddy has a little husky 235 and he cuts wood with this saw that ya could'nt even imagine.... I mean he really works this little saw. Anyhow his bar oiler quit working and I tore it apart for him to find that the little gear on the oil pump shaft is wore bad. Does anyone have a little 235 or another saw that the parts would interchange with laying around that would have the oil pump shaft and gear?

Shoot me a PM if ya can help me out.

BUMP... also I'm in the market for a good running GREEN poulan 3700.

 

[tbone75]

i have a little poulan model 2025,,its 36cc,, i need the adaptor plate that goes between the carb and cylinder,, the number on the back of it is 530049700 m1548,, i have some cash and a lot of lint

I think I found one?This it?

 

[Mastermind]

I'm seeking a top end for a Poulan Pro 330 or 380. I have some of that nasty green stuff to trade. Someone with more knowledge on these saws could help out with any interchangeable model numbers and I wouldn't mind at all.

 

[surfincr]

looking for a 16-18" bar and chain for a homelite super xlao

have a homelite 150ao that needs a new p&C with bar to trade or cash

 

[Eccentric]

looking for a 16-18" bar and chain for a homelite super xlao

have a homelite 150ao that needs a new p&C with bar to trade or cash

I have a good used hardnose Homelite 16" bar for your SXL-AO. What bar and chain (cut length, type, pitch) do you have with the 150? If it's 16", then I'll trade you bar for bar (I can use it on a Super E-Z). Keep that dang 150 powerhead (bet somebody else here would want it for parts anyways) and you can use that same chain on the bar I send you (if it's a 3/8" chain). They use the same # of drivers. If it's a .325 sprocket nose bar and chain, then I'll send you a loop of 3/8" chain with the bar.

 

[tbone75]

I'm seeking a top end for a Poulan Pro 330 or 380. I have some of that nasty green stuff to trade. Someone with more knowledge on these saws could help out with any interchangeable model numbers and I wouldn't mind at all.

The 330 will work on the 2700.But it takes a little work.Ask Jimdad in the sure is quiet thread?He did one.I used a top end off a 3500,3600,3800 60cc saw?Can't ???I put it on a 2800/48cc craftsman/poulan.Bolts right on.

 

[Jon1212]

I have a good used hardnose Homelite 16" bar for your SXL-AO. What bar and chain (cut length, type, pitch) do you have with the 150? If it's 16", then I'll trade you bar for bar (I can use it on a Super E-Z). Keep that dang 150 powerhead (bet somebody else here would want it for parts anyways) and you can use that same chain on the bar I send you (if it's a 3/8" chain). They use the same # of drivers. If it's a .325 sprocket nose bar and chain, then I'll send you a loop of 3/8" chain with the bar.

Aaron, I've got a Super EZ bar if you strike out. Don't sell those 150's short, Homelite new what they were doing when they called it a 150. It'll break down, and take 150 pulls before the owner smashes it......................:biggrin:

 

[tbone75]

Aaron, I've got a Super EZ bar if you strike out. Don't sell those 150's short, Homelite new what they were doing when they called it a 150. It'll break down, and take 150 pulls before the owner smashes it......................:biggrin:

Now why did you have to go and say that!Just after I get 2 of them! :hmm3grin2orange: I just think they look cool!

 

[surfincr]

I have a good used hardnose Homelite 16" bar for your SXL-AO. What bar and chain (cut length, type, pitch) do you have with the 150? If it's 16", then I'll trade you bar for bar (I can use it on a Super E-Z). Keep that dang 150 powerhead (bet somebody else here would want it for parts anyways) and you can use that same chain on the bar I send you (if it's a 3/8" chain). They use the same # of drivers. If it's a .325 sprocket nose bar and chain, then I'll send you a loop of 3/8" chain with the bar.

its a sprocket nose 18" 72dl its the stock bar with oregon chain i believe its the .325

 

[Scooterbum]

Now why did you have to go and say that!Just after I get 2 of them! :hmm3grin2orange: I just think they look cool!

They are cool looking till ya' have to work on one.
Gutsy little saw though. Typical for Homies of that era.
I got mine runnin' and gave them to new homes so I wouldn't have to work on them again.

 

[sefh3]

They are cool looking till ya' have to work on one.
Gutsy little saw though. Typical for Homies of that era.
I got mine runnin' and gave them to new homes so I wouldn't have to work on them again.

Can I send you two of them, you get em running and send them back??????

 

[huskydude]

Hey ya'll looking for a large mount bar for a Stihl 056 Would like a 24+ Also a clutch cover if someone has one? Condition of both doesnt matter as long not broken or To bad!

Also looking for some Stihl 290 parts. Muffler, 4 Cylinder bolts and a good coil.

Back home??

I got a rollmatic es 20", #3003 000 8822 if you decide on a smaller one. Little worn but usable.

 

[67L36Driver]

Aaron, I've got a Super EZ bar if you strike out. Don't sell those 150's short, Homelite new what they were doing when they called it a 150. It'll break down, and take 150 pulls before the owner smashes it......................:biggrin:

While we are on the subject of Homelite bars, is this a K095 mount?
View attachment 198249

Shown on top of an 20" Oregon #200---D196. Slot is .331" wide.
Faint markings: ??29 Homelite
GVA 16503

Was in the box with the ebay XL-101 parts saw.

Jon1212: Lets update the picture of the little guy 'grandpa'. ROFL

 

[tbone75]

They are cool looking till ya' have to work on one.
Gutsy little saw though. Typical for Homies of that era.
I got mine runnin' and gave them to new homes so I wouldn't have to work on them again.

:hmm3grin2orange: Sounds like I am in for some fun? NOT !!!

 

[komatsuvarna]

Ive got a stihl 009L that Id trade for a stihl or husky professional line builder saw....or Id sell it straight out. Saw runs good, just don't have no use for it anymore.

View attachment 198253

 

[ChainsawmanXX]

Back home??

I got a rollmatic es 20", #3003 000 8822 if you decide on a smaller one. Little worn but usable.

No such luck
Up in Vermont now, climbing the hills and dodging the detour sings.
It was nice meeting you Sal (Is that how you spell your name? Sorry)

I might actually have some use for that bar. Let me get back with you on that Thanks

 

[huskydude]

No such luck
Up in Vermont now, climbing the hills and dodging the detour sings.
It was nice meeting you Sal (Is that how you spell your name? Sorry)

I might actually have some use for that bar. Let me get back with you on that Thanks

Saul actually. It was nice to meet you as well!
I hope you enjoy your trip to New England.

 

[ARsawMechanic]

Would anybody have a crankcase for a stihl ms 660?

 

[PB]

Looking for a Jonsered 625 crankcase. I have some parts to trade and some Stihl bars and chains that I don't need. One is a brand new 20" Oregon Powermatch with new chain.

Still looking for a 2159 fuel tank also.

Shoot me a PM if you have something. I don't check the this thread very often.