Swap meet...

[tbone75]

I could use a coil for a Stihl 021-025. I have one from a MS series but it doesn't fit the crankcase. I have parts to trade and $$.

Hey you forget me?LOL I may have one?Need to look around.

 

[little possum]

BBB is good people. Not much street cred here, but he stays busy, mostly helping me!

 

[crane]

Mall 2MG

Kind of obscure, but thought I'd give it a shot.

Looking for complete carb and muffler assembly for a Malll 2MG(U.S. Forestery Saw) restoration. Could have odds to trade or good ol cash

 

[tbone75]

I could use a coil for a Stihl 021-025. I have one from a MS series but it doesn't fit the crankcase. I have parts to trade and $$.

Coil pics.Let me if you think it will fit?Its your if so.You may be able to help me out (again) some day? LOL PM me your address again I lost it?

 

[Mastermind]

BBB is good people. Not much street cred here, but he stays busy, mostly helping me!

BBB (Alex) has cred with me. I've met him in person and will say he is a great guy. I've also done some trading with him and was most pleased with that outcome too.

 

[little possum]

Kind of obscure, but thought I'd give it a shot.

Looking for complete carb and muffler assembly for a Malll 2MG(U.S. Forestery Saw) restoration. Could have odds to trade or good ol cash

Not that I can help, wish I could. But are you looking for a Tillotson ME Float Type or HP Diaphragm? Or would it matter?

 

[tbone75]

I have some small Poulans I would like to trade for something?Could use some more projects?Pro 220 nice shape,Pro 260 not bad either,New 3314,295 farmer in good shape plus a Stihl 012 good runner Stihl white 009L & a 009 in Orange Plus a Homelite Ranger & Bandit 33cc saws.They all run good!

 

[Bowtie]

Still needing a 372 cylinder. Also need another 046/460 cylinder. Have $$ or lots of junk to trade.

I have a good 046 cylinder. What ya have in mind?

 

[Duke Thieroff]

Looking for an 440 magnum top end, muffler and tank, plenty to trade


Chris

 

[timberdollars]

630 PC pics

I have a 1984 jonsereds 630 S piston and cylinder, 48mm, thin rings. CLOSED PORT 10:1 comp. ratio Fits 625,630, 61,162, 66, 266 (reduced size) etc etc

NO scoring or scratches on either, still has most machine marks on skirts.

I used this saw for couple seasons, great runner. very low hours!!!!!!! Just want someone to be able to use it, too good to sit around.

Trades for Partner parts, 2051 recoil, Poulan 475-505 stuff

Forgot this is very minor ported, no raise or lower, not alot just a cleanup woods port.

 

[crane]

Not that I can help, wish I could. But are you looking for a Tillotson ME Float Type or HP Diaphragm? Or would it matter?

Tillotson ME. I'd like to keep it original.

 

[o8f150]

i need a few parts for my newly aquired 288xp,, i need the idle screw,, bar adjustment screw and also a flywheel(2 fins broke off),, i have a complete husky 50 with a smoke piston i would trade for the flywheel,,plus i have cash

 

[mdavlee]

Looking for a 394 runner or builder. Rough looking is fine with me. Prefer complete saw in either condition. Have a few 066 parts and some green paper with pictures.

 

[nmurph]

I have a 1984 jonsereds 630 S piston and cylinder, 48mm, thin rings. CLOSED PORT 10:1 comp. ratio Fits 625,630, 61,162, 66, 266 (reduced size) etc etc

NO scoring or scratches on either, still has most machine marks on skirts.

I used this saw for couple seasons, great runner. very low hours!!!!!!! Just want someone to be able to use it, too good to sit around.

Trades for Partner parts, 2051 recoil, Poulan 475-505 stuff

Will this fit a 61 Practica?

 

[komatsuvarna]

Looking for a handle bar, handle bar brace, and chain brake handle for a 2083 Jonsered. I think a 2077 will interchange, along with the Poulan Pro 475/505, and Partner 660/7700....and there may be others. Thanks

 

[paccity]

Kind of obscure, but thought I'd give it a shot.

Looking for complete carb and muffler assembly for a Malll 2MG(U.S. Forestery Saw) restoration. Could have odds to trade or good ol cash

let me dig through some box's , i'll pm ya if i'm sucsesfull.

 

[jimbo1490]

I have about 30 or so Husky flywheels and you know they kinda all look the same:msp_unsure: Do you know the P/N of the flywheel you have now?

Jimbo

i need a few parts for my newly aquired 288xp,, i need the idle screw,, bar adjustment screw and also a flywheel(2 fins broke off),, i have a complete husky 50 with a smoke piston i would trade for the flywheel,,plus i have cash

 

[timberdollars]

630 cylinder for 61 practica

Will this fit a 61 Practica?

Good question, not to sure about that, I want to say yes, but check first. This fits 61 with white or grey tops!!!! Someone should be able to say for sure on here.

 

[timberdollars]

2083 parts

Looking for a handle bar, handle bar brace, and chain brake handle for a 2083 Jonsered. I think a 2077 will interchange, along with the Poulan Pro 475/505, and Partner 660/7700....and there may be others. Thanks

Not real easy to find parts, all those models plus the Poulan 415 425 and 445 will fit. (very rare) Some available new still too. If it doesn't work out I'd be interested in the saw. I seem to be addicted to them in any color!

 

[skycranemech]

john deere 80 ev parts

looking for a Handle, cushion & stopper for handle, and the bar cover/guide cover. for John deere 80 ev. Or believe Echo equivilant is cs-370 evl. thanks. Bob Wallach.

(six,three,six)- 262-8546