Swap meet...

[nmurph]

Might be hard to find, good luck.

Just so you know from Poulan.

530071321 PISTON KIT 48.65

I was just hoping to find a good used one or a spare on someone's shelf. The Greek has Episan 335 pistons for $32+shipping.

 

[nmurph]

Will this one fit?

OREGON POWER MATE SPROCKET SYSTEM HUSQVARNA 140,240,340,444 | eBay

I don't know, but that auction is over. I'm fixing this saw for a neighbor who made the mistake of taking it to the local NAPA store for a sprocket. The oiler gear was stripped when he got it back. I know Bailey's has the conversion kit, but I was hoping to find one on here.

 

[Saw Dr.]

Any chance any of you fellas have a good crankshaft for an MS 390 with good main bearings?


Chris

They're just standard 6203 c3 bearings. Any bearing house can get them for you. Probably just over $10 each for new ones.

 

[Bowtie]

They're just standard 6203 c3 bearings. Any bearing house can get them for you. Probably just over $10 each for new ones.

They can get the seals too.

 

[bigblockburris]

MS290, 310 and 390

They can get the seals too.

Anybody got a good number for the seals? Thanks for the bearing number Tim!

I need for MS290, 310 or 390
-Nice air filter cover
-Both flippy caps

Needed for a 036 Pro
-Flat-top cover with decomp ( I have a nice MS360 cover to trade)
-Flat top airfilter cover
-Air filter

I have 026/260 parts and some other Stihl parts and greenbacks to trade.

Thanks!

BBB

 

[Bowtie]

Anybody got a good number for the seals? Thanks for the bearing number Tim!

I need for MS290, 310 or 390
-Nice air filter cover
-Both flippy caps

Needed for a 036 Pro
-Flat-top cover with decomp ( I have a nice MS360 cover to trade)
-Flat top airfilter cover
-Air filter

I have 026/260 parts and some other Stihl parts and greenbacks to trade.

Thanks!

BBB

9639 010 1743, or 9639 003 1743 for the seals.

I have a new curved top filter cover for a 290-390 saw.

 

[Saw Dr.]

I don't know, but that auction is over. I'm fixing this saw for a neighbor who made the mistake of taking it to the local NAPA store for a sprocket. The oiler gear was stripped when he got it back. I know Bailey's has the conversion kit, but I was hoping to find one on here.

Ahh yes, the old favor for the neighbor trick. Very well versed at that one myself. Almost always turns into a huge can of worms. Good luck.

Anybody got a good number for the seals? Thanks for the bearing number Tim!

I need for MS290, 310 or 390
-Nice air filter cover
-Both flippy caps

BBB

If Jason does not fix you up on the 290 filter lid, let me know. I think all my spare flippys are broken (go figure....) THe OEM seals are 17mm x 30mm x 4.4mm. I have NEVER seen 4.4mm thickness seals available in the aftermarket. You can squeeze ones a little thicker in there, but 7mm is going to be WAY to big. The seals are about $15+ EACH from you dealer, so try aftermarket ones if you can find them. I have not tried THESE yet, but may on the next order. There are two different seals from Stihl, and one is used in a complete engine. I have never tried them, though I bought them accidentally a few times. I always went back to the correct ones, so I still have the wierd ones here.

 

[o8f150]

I think I have one for you, it's gonna cost you though...at least $0.10.

thanks pm sent

 

[nmurph]

Does anyone have a spare 036 cylinder?? Government IOU's to swap.

 

[jimbo1490]

I don't know, but that auction is over. I'm fixing this saw for a neighbor who made the mistake of taking it to the local NAPA store for a sprocket. The oiler gear was stripped when he got it back. I know Bailey's has the conversion kit, but I was hoping to find one on here.

Yes, I know the auction is over. But it happens that I'm the winner and I'm holding the drum in my hand right now. I bought it for another saw but wound up not needing it.

Jimbo

 

[sefh3]

If Jason does not fix you up on the 290 filter lid, let me know. I think all my spare flippys are broken (go figure....) THe OEM seals are 17mm x 30mm x 4.4mm. I have NEVER seen 4.4mm thickness seals available in the aftermarket. You can squeeze ones a little thicker in there, but 7mm is going to be WAY to big. The seals are about $15+ EACH from you dealer, so try aftermarket ones if you can find them. I have not tried THESE yet, but may on the next order. There are two different seals from Stihl, and one is used in a complete engine. I have never tried them, though I bought them accidentally a few times. I always went back to the correct ones, so I still have the wierd ones here.

I have used these seals. I have not had a problem at all with them. I have them on 4-5 290's and 5-6 MS250's. Yes they are thicker but all saws have passed leak tests and have a dozen of tanks through them.

 

[sefh3]

They're just standard 6203 c3 bearings. Any bearing house can get them for you. Probably just over $10 each for new ones.

I found my at my local NAPA. Cost was $5 each for them. Mine came sealed but was easy to use a pick and get the seals off.

 

[barneyrb]

looking for a dolmar 115i piston or even just rings, 44mm i think, 111 is the same,

If you haven't found anything yet let me know....

 

[SawGarage]

Bought a 350 Husky cover on Ebay...

guy charged $10 to ship it (wouldn't offer actual, or accept a bit more for packing..) shows up with a tag for $3.70 from USPS

take the cover out, band is busted, cover is broke in two places, and cracked as well...

Now he wants me to return it, BUT did not offer returns?

THEN threatens "this better be my cover, as mine was in good shape, and the band was not broken!!!!"

I feel my trash isn't much different than Florida trash??

sometimes I HATE ebay....





SO, anyone have a decent clutch/brake cover for a 340-359?? I have parts to trade if so.

 

[DSS]

does anyone have a good oil pump assembly for a huskie 36,,dang thing still won't pump,,,, i believe a 41 is the same,, i have some green crapy paper to trade

I got one if Jacob doesn't. I want .15 cents for mine though.

 

[wigglesworth]

Bought a 350 Husky cover on Ebay...

guy charged $10 to ship it (wouldn't offer actual, or accept a bit more for packing..) shows up with a tag for $3.70 from USPS

take the cover out, band is busted, cover is broke in two places, and cracked as well...

Now he wants me to return it, BUT did not offer returns?

THEN threatens "this better be my cover, as mine was in good shape, and the band was not broken!!!!"

I feel my trash isn't much different than Florida trash??

sometimes I HATE ebay....





SO, anyone have a decent clutch/brake cover for a 340-359?? I have parts to trade if so.

U sure do cry alot....

 

[SawGarage]

U sure do cry alot....

ya offering help???

crying?? hmm, maybe I do... (my luck SUCKS, what can I say...)

on the CRYING I learned it was the thing to do from a Guy named Jeremy in W. Kentucky.... :check:




just exemplifying that PEOPLE suck...

 

[o8f150]

I got one if Jacob doesn't. I want .15 cents for mine though.

thanks dss but JJ just sent me a message that he has one heading my way

 

[Madsaw]

Jay, I forgot your tracking numbers again. Its raining here this morn I will get on it. Unbelievable dec30 and pouring rain. High tomorrow is suppose to be 45. I thought I was in wis.
Jay do you have any parts for a 450
Bob

 

[SawGarage]

Jay, I forgot your tracking numbers again. Its raining here this morn I will get on it. Unbelievable dec30 and pouring rain. High tomorrow is suppose to be 45. I thought I was in wis.
Jay do you have any parts for a 450
Bob

Bob,

Might they be in a Stihl and a Echo box? if so, they are on the front porch .. I'm home on Bereavement for the Gramps (yeah, I might be crying again, there Jeremy... )

450, as in husky? or J-red?

I have a few things...what are you needing??

J