Swap meet...

[Scooterbum]

I have a new Oregon Pro Lite 18" 66DL bar for stihl. Also have a fresh set of Carlton chain for it. I am in need of a 24" bar for a small mount mac or Husqvarna bar for small mount in 20-24". Whatcha got?

I,ve got a couple 24" Mac bars. Let me check the mount pattern. I could use that 18".

 

[Scooterbum]

I have an 028-44mm, 045/56- 54mm, 056magII 56mm cylinders also Sachs/Dolmar 120 P&C to trade or sell.

Need? see signature also 044 10mm pin type piston needed.

Bump

 

[Warped5]

looking for a dolmar 115i piston or even just rings, 44mm i think, 111 is the same,

PM MechanicMatt ... he had a bunch of 111 parts.

 

[Saw Dr.]

I need a recoil assy and a blower tube throttle assy for an Echo PB-650. Anyone have a dead one kicking around?

 

[nstueve]

J-red parts Clearified...

Needed for the 630:
http://www.jonsered.ws/630.pdf
Handle gas tank: 501 77 27-03 or 501 77 27-04
Side grips: 503 48 45-02

Needed for the 2095:
http://www.jonsered.ws/2095.pdf
Choke Lever: 503 64 68-01

Boring old $$$ to trade...

 

[Duke Thieroff]

Any chance any of you fellas have a good crankshaft for an MS 390 with good main bearings?


Chris

 

[nstueve]

Any chance any of you fellas have a good crankshaft for an MS 390 with good main bearings?


Chris

pm sent... might be able to work something out...

 

[nmurph]

I'm looking for a 18" big mont husqvarna bar in .050ga, 3/8 pitch and 68DL. Have these to trade:

18" K095 mount (small mount - Husqvarna) powermatch, 68DL - .050ga - 3/8 (bar only)
View attachment 213237

OR

20" K095 mount (small mount Husqvarna) Carlton, 72DL - .058ga - 3/8 (bar only)
View attachment 213238

I have a brand new 20" Total D009 mount. It's a hardnose, but a beautiful piece of work. I would be interested in the 18".

 

[tbone75]

Looking for a 044 tank and air filter cover.About all I got to trade is dirty green paper TIA

 

[Madsaw]

Needed for the 630:
http://www.jonsered.ws/630.pdf
Handle gas tank: 501 77 27-03 or 501 77 27-04
Side grips: 503 48 45-02

Needed for the 2095:
http://www.jonsered.ws/2095.pdf
Choke Lever: 503 64 68-01

Boring old $$$ to trade...

Might have one will check.
Bob

 

[tbone75]

This cold be a long shot? I need a clutch cover for a Echo 601S TIA

 

[MechanicMatt]

PM MechanicMatt ... he had a bunch of 111 parts.

It was actually a 115i, and I no longer have it. Three members on here ended up with bits and pieces of it. The P&C were the first to go, I wish I could help.

 

[plumbcrazyjr]

I have a 115 pm me if you need parts off it

 

[super3]

I might have an extra brand new in-box OEM...

Im am on that like a fat kid on a cupcake.

If it turns out JJ doesn't have one, I do.

 

[o8f150]

does anyone have a good oil pump assembly for a huskie 36,,dang thing still won't pump,,,, i believe a 41 is the same,, i have some green crapy paper to trade

 

[nmurph]

I'm looking for either of following for a 345-

a spur drum and oiler drive gear

or

a rim and drum set-up with the oiler gear.

These are not the same pieces used on a 346.

 

[nmurph]

I'm looking for a PP335 piston.

 

[Modifiedmark]

I'm looking for a PP335 piston.

Might be hard to find, good luck.

Just so you know from Poulan.

530071321 PISTON KIT 48.65

 

[Jacob J.]

does anyone have a good oil pump assembly for a huskie 36,,dang thing still won't pump,,,, i believe a 41 is the same,, i have some green crapy paper to trade

I think I have one for you, it's gonna cost you though...at least $0.10.

 

[jimbo1490]

I'm looking for either of following for a 345-

a spur drum and oiler drive gear

or

a rim and drum set-up with the oiler gear.

These are not the same pieces used on a 346.

Will this one fit?

OREGON POWER MATE SPROCKET SYSTEM HUSQVARNA 140,240,340,444 | eBay