Swap meet...

[Jacob J.]

I bought a used 660 and came with 24 and 28 in bar. the 24 was used the most and i want to widen the gap a little wtt 28 for 36 or 32 b&c. The 28 has very little use on it . shoot me an e mail and i can send pics. Thanks

What gauge are you looking for? I have a Stihl ES 36" in 3/8" x .050" gauge.

 

[deerjackie]

What gauge are you looking for? I have a Stihl ES 36" in 3/8" x .050" gauge.[/QUOTthats what my bar is 3/8 x50 i have photos on my phone. bar and chain has barely been used text me at 731 363 5401 and i can show you a photo or shoot me a pm with your email and photo of your bar. and chain. just need to widen the gap for that every now and then tree.. thanks ps ts a rollmatic es also

 

[psuiewalsh]

You got anything to trade? I may have an 044 filter base you're looking for. Have to go look in my boxes.

I'm looking for Stihl stuff, 064 and 660/066.

Any interest in this 064 stuff? Looking for HD air filter setup for my 064.

 

[psuiewalsh]

UFO parts

These were in with some small Mcculloch parts. Not sure what they fit. Don't see numbers, don't want to throw them out either.

 

[forestryworks]

Any interest in this 064 stuff? Looking for HD air filter setup for my 064.

PM sent.

 

[o8f150]

hey guys,,, i just got the ms210c today,, i am building it for my wife since she doesn't like teh 346xp that much,, thank goodness,,,, anyway i need a starter assembly and also the clutch cover,, i am looking for the standard recoil and clutch cover (2 hole) not the easy tension and the easy start,,i have cash and some parts for trade

 

[DSS]

These were in with some small Mcculloch parts. Not sure what they fit. Don't see numbers, don't want to throw them out either.

I'm fairly sure that muffler's off a 3270 Pioneer.

 

[jbird77]

Husky

I have a coil n a muffler for a husky 36 if any one is needing them .

 

[psuiewalsh]

homelite/textron and Eager Beaver

Anyone need some multicolored door stops?

 

[stihlboy]

Once again ill ask, I need 084 parts, carcasses.

I have a ton of Stihl NOS parts.

I need tons of 084 parts. Please help thanks.

still need

 

[MEATSAW]

I am in need of an 028 complete air filter. Can anyone help?

 

[nmurph]

Going fishing; hoping for good luck!!

I need a-

281 Throttle lever bellows
281 carb partition
281 muffler heat shield


365 CP cylinder or 372 P/C

S&H Green Stamps for trade.

394 FW nut

 

[Modifiedmark]

i found that out earlier:bang::bang::bang: more then likely i will just have to get another easy start recoil,, i t will be just as cheap that way,, it may be easier for her to start

Scott, will a ms250/025 cover and flywheel work? I know I have the recoil but will have to see if I still have the flywheel or not.

 

[o8f150]

hey guys,,, i just got the ms210c today,, i am building it for my wife since she doesn't like teh 346xp that much,, thank goodness,,,, anyway i need a starter assembly and also the clutch cover,, i am looking for the standard recoil and clutch cover (2 hole) not the easy tension and the easy start,,i have cash and some parts for trade

hey guys,, muddawg had the clutch cover and chainsawr had a good looking easy start recoil assembly so i went ahead and ordered it,, so i am good to go,,,,thanks guys

 

[sefh3]

Scott, will a ms250/025 cover and flywheel work? I know I have the recoil but will have to see if I still have the flywheel or not.

I could use the flywheel cover, if no one else has claimed it. Also need a good clutch cover for one too.

 

[Arrowhead]

Sorry for the dirty laundry post guys. I don't normally do that. I've been holding it in for over a year now..... I do feel a little better though.
It's not just me either, Mark and a couple other well respected members had similar dealings.

Anyways, to get back to the junk swapping.... I could use a ms310 piston, clutch, carb and other stuff.
Got buckets of trading stock.

 

[wyk]

Echo CS-510 or 520

Hey guys, I came across a pair of straight gassed Echo's and was wondering if anyone had a line on some pistons and rings? Baileys want's 50 a pop

Cheers

 

[bplust]

Speaking of Echo, I have a cs-5500. It's dirty, the brake handle isn't there, but the motor's in great condition, it looks good and it clocks in at 170psi.

However, it has no spark.

I don't know if it's the primary or secondary coil, so I guess I'm looking for both just in case, or even better, for someone to take this off my hands. Comes with a used 16" bar and chain if interested.

 

[barneyrb]

Speaking of Echo, I have a cs-5500. It's dirty, the brake handle isn't there, but the motor's in great condition, it looks good and it clocks in at 170psi.

However, it has no spark.

I don't know if it's the primary or secondary coil, so I guess I'm looking for both just in case, or even better, for someone to take this off my hands. Comes with a used 16" bar and chain if interested.

The 5500 is notorious for burning out ignitions. I have a buddy with three of them, none of which have any spark.

BTW- did someone from this thread try to call me today? I got a call from a Mississippi number, I couldn't understand what was said. When I tried to return the
call, I get an error message "This call cannot be completed as dialed."

I don't know if it applies to these saws but Echo has a lifetime warranty on SOME ignition systems. They replaced a coil on a 670 at N/C for me. It might be worth a try.......

 

[eiklj]

I got a Remington Mighty Mite for sale or trade

I have no clue whats this thing is worth

You still have that Mighty Mite for sale?
PM me if you still do.

je