turbo885
ArboristSite Operative
i have 3 new 16" 3/8 050 gb bars View attachment 225993View attachment 225994
Swap meet...
- Thread starter Four Paws
- Start date
Help Support Arborist Forum:
I am for sure...
Eccentric
Mister Wizard
xtremez
ArboristSite Guru
xtremez
ArboristSite Guru
I have the following, everything must go:
2 Poulan S25D's - Give em' some carb work and they're good to go.
1 Poulan S25CVA - Same deal, plus need to repair/replace lower handlebar mount.
1 Homelite 350 - Tune it an it's good to go.
Homelite Super EZ parts
Homelite SXL/XL-12 parts
PM me if you're interested in anything. Regarding trades, (and if you're not interested in anything, I am looking for this stuff!):
NOS McCulloch 7-10 parts, McCulloch S-44 air filter cover, McCulloch 550 clutch
2 Poulan S25D's - Give em' some carb work and they're good to go.
1 Poulan S25CVA - Same deal, plus need to repair/replace lower handlebar mount.
1 Homelite 350 - Tune it an it's good to go.
Homelite Super EZ parts
Homelite SXL/XL-12 parts
PM me if you're interested in anything. Regarding trades, (and if you're not interested in anything, I am looking for this stuff!):
NOS McCulloch 7-10 parts, McCulloch S-44 air filter cover, McCulloch 550 clutch
parrisw
Tree Freak
MS460WOODCHUCK
Addicted to ArboristSite
I just sold a titan junior 200...had no idea he was looking for 1:msp_sad:
parrisw
Tree Freak
A 2 man is better.
NOS Homelite 330 clutch springs, or a good clutch, anybody? I've tried several used clutches that felt a lot better than the one that came with the saw and didn't get the results I wanted, so I might have to go the NOS route, but if you have a known good clutch, I'm interested.
Homelites need a new home!
Throw me some offers...
Homelite Super XL Automatic (58cc) 140+psi broken air cleaner cover
Model Profile: XL AUTOMATIC
Homelite SuperEZ Automatic (41cc) 130psi broken clutch cover
Model Profile: SUPER EZ AUTO
Throw me some offers...
Homelite Super XL Automatic (58cc) 140+psi broken air cleaner cover
Model Profile: XL AUTOMATIC
Homelite SuperEZ Automatic (41cc) 130psi broken clutch cover
Model Profile: SUPER EZ AUTO
Eccentric
Mister Wizard
What about the blue one that I asked about in the 2-man thread today Will? I can hook Jacob up with it.....
parrisw
Tree Freak
Cool. I missed a big blue two man a couple years ago.
thomas1
sodium pentothal
- Joined
- May 2, 2010
- Messages
- 3,651
- Reaction score
- 1,092
I need to make some room, anybody need one or all of these?
Runs fine
Has compression, I haven't messed with it beyond that. Appears to be complete.
Complete, minus the powersharp parts. No guarantees beyond that. Some corrosion on a few edges.
Runner.
Parts only, muffler was loose and melted a hole in the top of the tank.
runner, new fuel line. Needs an airfilter.
What you see is what you get. I haven't touched the chains on these either, maybe that's a good thing.
Runs fine
Has compression, I haven't messed with it beyond that. Appears to be complete.
Complete, minus the powersharp parts. No guarantees beyond that. Some corrosion on a few edges.
Runner.
Parts only, muffler was loose and melted a hole in the top of the tank.
runner, new fuel line. Needs an airfilter.
What you see is what you get. I haven't touched the chains on these either, maybe that's a good thing.
MechanicMatt
Cut Split Stack Burn
14 inch B&C .325 for a stihl 025 also a 42cc wildthing motor, have bits for a super2, wildthing pieces, and 031 tidbits. The 031 stuff is going quick though.
Last edited:
I'm parting out a Husqvarna L65. Let me know if you need anything.
I need a clutch cover for an MS361 and a piston for an 024. Have some 024/026 parts and green stuff.
Matt, the best I could come up with is a 16" .050 hardnose or a 14" 3/8 lopro Intenz bar.
I'll send you one free if you think you could use one or the other.
The 14" would be a better choice in my opinion... you can get a 3/8 lopro picco drum on ebay for $10, or somebody here may have one.
PM me if interested.
Then I'm glad I refered him to you Jacob!
Wish somebody (cough, cough) would've referred him to me. :msp_sad:
