Swap meet...

[little possum]

Have a friend looking for a 28-32" large mount husky bar....He has $ for trading fodder.

 

[deerjw]

015 Hedge Trimmer Attachment

I hope this is the right place to post that I'm looking for a hedge trimmer attachment for a Stihl 015.

 

[thomas1]

See Aaron's post.....

I think I have mostly 5- or 7- stuff but, lemme dig a little.

 

[Modifiedmark]

I need a front handle for a Poulan 4200/5200 if anyone has one it good shape to trade.

 

[nstueve]

076 parts...

anyone happen to have a 58mm 076 piston (NOS or good quality AM)? A couple guys happened to have my dolmar9010 piston so thought I would ask...

Also need to know the part number for the ignition module/trigger or a link to one on the internet! Mitch (mweba) thought I could get one at radio shack but I wouldn't know what to ask for. I think it's getting hot and keeping the saw from restarting...:msp_unsure: any help appreciated!

 

[Jacob J.]

I need a front handle for a Poulan 4200/5200 if anyone has one it good shape to trade.

Mark-

I think I have a 4200/5200 handle you can have if you'd be satisfied with a half-wrap.

 

[Jacob J.]

We have our Homelite series from the 360 - 750 complete with the exception of a 550. I think we have a deal in the works for that one though.

We have been looking at acquiring some of the early '60 vertical cylinder Homelites.........I would be interested in trades.

Randy-

In addition to the 550, I have many of the 900-series vertical cylinder Homelites, so I can set you up with one or more of those.

 

[homelite028]

needing a p51 crank case or p50 a junk saw

any body have a p51 pioneer crank case they dont need or junk p51 or p50 as long the crank case is good

 

[wendell]

We have our Homelite series from the 360 - 750 complete with the exception of a 550. I think we have a deal in the works for that one though.

We have been looking at acquiring some of the early '60 vertical cylinder Homelites.........I would be interested in trades.

How many Zips ya want? I do have a 395 that needs ported.

 

[Arrowhead]

any body have a p51 pioneer crank case they dont need or junk p51 or p50 as long the crank case is good

Ben, I'll check in the morning.

 

[Mastermind]

Randy-

In addition to the 550, I have many of the 900-series vertical cylinder Homelites, so I can set you up with one or more of those.

One would be fine to start with JJ.

How many Zips ya want? I do have a 395 that needs ported.

I'm not so interested in the Zips or the EZ....

That 166 you have though....... :hmm3grin2orange:

 

[wendell]

I'm not so interested in the Zips or the EZ....

That 166 you have though....... :hmm3grin2orange:

I thought you were good at what you do....


and you're definitely not that good. :hmm3grin2orange:

 

[Mastermind]

I thought you were good at what you do....


and you're definitely not that good. :hmm3grin2orange:

No port job is good enough for that trade.



We finally got that old Homelite 750 almost finished. We were able to make a few cuts with it. It even oils just as it should. :msp_thumbup:

 

[Nogoingback]

Large spike set for a Jonsered 670 and a SP125 crank stuffer needed. Chains and parts for trade or green stuff.

If you have a pipe and header that will work on a stock 101 and it's taking up valuable room, I may be interested in that too.

 

[RedneckChainsawRepair]

I'm not so interested in the Zips or the EZ....

That 166 :hmm3grin2orange:

2 runners I had and 3rd one was never put together and was just used as parts saw. Even had brand new coil and bunch of parts I threw in as a package deal.

I never want to wrench or run a 166 again. :msp_tongue:

 

[tbone75]

Need a P&C and muffler for a 064.Got some things to trade or green backs. TIA

 

[tbone75]

2 runners I had and 3rd one was never put together and was just used as parts saw. Even had brand new coil and bunch of parts I threw in as a package deal.

I never want to wrench or run a 166 again. :msp_tongue:

To bad,I know someone who would love to have one! :msp_rolleyes:

 

[Scooterbum]

Need a P&C and muffler for a 064.Got some things to trade or green backs. TIA

Ya' in a hurry?
If not I will have both when Master Dude gets a 066 cylinder up to me.

 

[tbone75]

Ya' in a hurry?
If not I will have both when Master Dude gets a 066 cylinder up to me.

No hurry at all! I am sure I can find something you like? LOL

 

[Mastermind]

Ya' in a hurry?
If not I will have both when Master Dude gets a 066 cylinder up to me.

And....."Masterdude" has the jug on my bench.....Durand does fine looking work.