Swap meet...

[Mastermind]

I'm not gonna lie........I got to laughing so hard when I read this that I peed a little.

Just a little huh? :msp_sneaky:

I'm gonna be leaving Sunday and won't be back till the next Sunday. Now I'm gonna want to leave someone in charge that has good sense while I'm away.......

Yeah......I'm stumped too.

 

[Trx250r180]

Just a little huh? :msp_sneaky:

I'm gonna be leaving Sunday and won't be back till the next Sunday. Now I'm gonna want to leave someone in charge that has good sense while I'm away.......

Yeah......I'm stumped too.

i say after 3 days no as you get the chills and shakes from withdrawl ,better pack the smart fone

 

[Arrowhead]

Still needing a P45/Poulan 455 piston.
My last request got lost in 5 pages of pie. umpkin2:

 

[nmurph]

...Just trying to keep you both from looking like DH1984...

Where is Charles?? I haven't missed him until now!

 

[o8f150]

AHA!!!!!!! Unless said owner/operator was in fact a midget, in which case it would have rubbed on his forehead, hopefully leaving the recoil unmarked.

Now everybody shut the #### up. I need a coil for a 488 shindaiwa, I ain't paying 5 bills for it, and I want some damn pie.:msp_sneaky:

dang man,, get your utters unknotted

 

[thomas1]

Making room.

064 runs, oils, cuts well. Missing front, lower left AV buffer. If I make it by the dealer I will grab one, the screw and plug/cap for it are included. The right cylinder cover bolt is stripped, I have an original screw but haven't decided whether to helicoil it or tap it bigger. Dual dogs, HD filter, Walbro carb (wj6 or wj10 I don't recall). 155psi on my gauge.

Bar is 24" to the tip from the spikes, the size is worn off. How do they measure Stihl bars?

It should clean up nicely.

Sold.

 

[RedneckChainsawRepair]

Believe me, I won't wonder. Thanks to Randy, your reputation precedes you.........LOL!!! Speaking of "reputation"..............repped...........*burp*

:msp_thumbsup: :msp_love: Busy :msp_biggrin:

 

[GeeVee]

This FastLEO151, are you on the job?

While I appreciate it hasn't been spit shined with "rebuilder-in-a-can" it was kind of an unremarkable saw to an extent.

Not wanting one, I wasn't going to look, but then I got caught up reading all the posts and couldn't stop.

I was going to read a few more posts, but instead I'm going to have some of my wife's pie. No floss needed.

 

[Jwalker1911]

Sold.

Due in no small part to the extreme media exposure......

 

[AU_K2500]

:msp_thumbsup: :msp_love: Busy :msp_biggrin:

That's the way to do right there....wait a second, I didn't know they taught folks in ohio about pecan pie and nilla ice cream....much less how to make pecan pie! Looks good!

 

[tbone75]

:msp_thumbsup: :msp_love: Busy :msp_biggrin:

That is just plain MEEN ! The not sharing ! Dang that looks good!

 

[AU_K2500]

im in need of a 455 rancher wrap/front handle and a 455 rancher ignition module. Ive got some parts/saws to trade.

 

[wendell]

I have met him in person......

He's younger than I am.......seems smarter too. :msp_unsure:

:taped::taped::taped:



Looking for an 064. Doesn't have to be pretty. Got greenbacks to trade.

 

[wendell]

:taped::taped::taped:



Looking for an 064. Doesn't have to be pretty. Got greenbacks to trade.

Dang, looks like I missed quite the party and my dream of owning a thomas1 saw.

 

[Madsaw]

:taped::taped::taped:



Looking for an 064. Doesn't have to be pretty. Got greenbacks to trade.

Wendell, Did you see the 200t listed on CL today around noon? He was from the east side and said it ran good just a broken chain brake handle.
Bob

 

[sefh3]

Where is Charles?? I haven't missed him until now!

Looking for that clutch side bearing for his 041.

 

[jnl502]

Looking for that clutch side bearing for his 041.

I think he has the bearing now, it's the saw he can't find now!:msp_w00t:

 

[sefh3]

I heard is was banned. Not sure how he did it because he was paying the sponsor fees.

 

[ChainFinn]

im in need of a 455 rancher wrap/front handle and a 455 rancher ignition module. Ive got some parts/saws to trade.

Can you give the modules ID number that you need ?

 

[sefh3]

I'm looking for a piston, rings, crank bearings and seals for a MAC Double Eagle 80. I have parts to trade.