Mastermind
Work Saw Specialist
I was always told that no is a complete sentence.....
Swap meet...
- Thread starter Four Paws
- Start date
Help Support Arborist Forum:
I was always told that no is a complete sentence.....
o8f150
Tree Freak
I would be happy to buy or trade you out of it? But you would have to mail it to me.Just can't ride in a car that far right now :msp_sad: I would like to come up for a visit some time? LOL
bout time for some more pecan pie and ice cream. :msp_tongue: piece from this morning has wore off. :hmm3grin2orange: bye
Just so you guys know pecans are $14 a lb or 6 ounces to make one pie is $6.79 and worth every dime for homemade.
Just so you guys know pecans are $14 a lb or 6 ounces to make one pie is $6.79 and worth every dime for homemade.
Forgot all about that. You got my email? If so I will give you my # and we can work a trade etc or something.
bout time for some more pecan pie and ice cream. :msp_tongue: piece from this morning has wore off. :hmm3grin2orange: bye
Just so you guys know pecans are $14 a lb or 6 ounces to make one pie is $6.79 and worth every dime for homemade.
Man! Just keep rubbing it in! :msp_razz:
This is going to cost you big time. I pulled the tank before I got my pie and ice cream. :msp_tongue:
This is going to cost you big time. I pulled the tank before I got my pie and ice cream. :msp_tongue:
:msp_ohmy: :help:
Chris, I have several of these 61 dogs, if you want one, I'll head one North.
I believe I have an extra adjuster here already. If I end up with the saw, I'll send one to you.
394 project
Here you go. A good project for you guys that want a 394. Everything for a Franklin and a Grant. Great muff, full wrap, gas tank, cylinder needs clean up from mild scoring, broken piston, one tank small chain strike hole leak. good cranks, one case with bad dawg holes and other good except for a small break in right front (cosmetic), oilers, flywheel, small parts galore, starters, everything. Come get it here or send somebody. (Near Sacramento.)
Will trade for 044/046 parts. I need the air filters, clutch covers, air filter cover plastic, and the hold down for the filter covers. bring with you when trading.
View attachment 244385 Mike
Here you go. A good project for you guys that want a 394. Everything for a Franklin and a Grant. Great muff, full wrap, gas tank, cylinder needs clean up from mild scoring, broken piston, one tank small chain strike hole leak. good cranks, one case with bad dawg holes and other good except for a small break in right front (cosmetic), oilers, flywheel, small parts galore, starters, everything. Come get it here or send somebody. (Near Sacramento.)
Will trade for 044/046 parts. I need the air filters, clutch covers, air filter cover plastic, and the hold down for the filter covers. bring with you when trading.
View attachment 244385 Mike
Chris...That dawg is on that 61 upside down, but if you want one, I'm sure I have one I can send you....It will fit the J'red.
Chris, it measures just over 2" center to center on the mount holes. If you want one, it's yours.
Ed, if Rob has one I might as well get it from him and save you the customs forms BS, but thanks brother. My Jred came with two of those stupid smooth ones....
8433jeff
Aftermarket connoisseur
Ed, if Rob has one I might as well get it from him and save you the customs forms BS, but thanks brother. My Jred came with two of those stupid smooth ones....
No problem Chris. My 61 came with Jred top cover/air cover and starter cover. If I get the one above, your welcome to those pieces if you want them. I think we struck a deal.
Duke Thieroff
Fill your hands, you SOB!
Looking for a few odds and ends here...
-Homelite 410 wrap handle, half or full is fine.
-Dolmar 6800i piston
-Husqvarna 268/272 OEM top end
Got trade meat and the like, tons of Poulan 3400/Craftsman 3.7 parts, Stihl 018 parts, Husky 50 parts, Mac 10 series stuff....
Chris
-Homelite 410 wrap handle, half or full is fine.
-Dolmar 6800i piston
-Husqvarna 268/272 OEM top end
Got trade meat and the like, tons of Poulan 3400/Craftsman 3.7 parts, Stihl 018 parts, Husky 50 parts, Mac 10 series stuff....
Chris
I think I have a good OEM 45mm or 46mm 029/290 jug if that helps?
cost ya a bore hone on my 9010 cylinder... what do ya think?
Also for anyone reading I have about 1/2 of a 1127... nice plastics, carb, coil... looking for crank case, crank and flywheel... Got some stihl bars and cash to trade.
Last edited:
I haz shtuff to trayde! moldy green stuff, icky orange parts (husky of course
