"You Suck" Thread 2019--Pics required!

[president]

I'm not sure if the husky is a 61 or a 266se? I can't read the I'd tag other than it says 82 and serial number and you can almost read SE way right of the 82 but either way I'm fixing it up once I figure it out.

Im thinking with the se it must be a 266, or 268

 

[Deleted member 117362]

I purchased a puzzle.

 

[Terrence Jefferson]

Just got this this week. Quick carb clean and fresh fuel and she runs sweet

 

[Deleted member 117362]

Puzzle solved.

 

[m2theb]

Picked up a 359 from the original owner, who stated it wouldn’t run. Bar/chain were original, no more than 10 tanks of fuel ran though it since he bought it. Used where he hunted to trim limbs in shooting lanes, but has sat up last couple years. Compression is great, put fresh fuel in it in his driveway and it fired up and ran but wouldn’t idle. I handed him the $35 he was asking and tossed it in the truck. One Zama carb later, she’s purring......View attachment 713043

Suckiest so far

 

[skytow]

Puzzle solved. View attachment 719706 View attachment 719707 View attachment 719708

Duce you do suck! Best puzzle ever....

 

[RAS61]

I purchased a puzzle.View attachment 719506

Well at least the parts look very clean, and so does the finished product!

 

[peak98]

Suckiest so far

I bought it to fix and sell, just can’t make myself list it. It runs so good, I’m debating a muffler mod on it.

 

[undee70ss]

Here’s mine, Oregon 10AC 1/2 pitch .063 gauge, 100 foot roll. I can’t believe no one else bid on this or even watched the auction.

 

[Ryan_289]

I picked this 026 up last week. Guy said it was hard to pull and had old gas in it. I offered $100 bucks and he took it. Drained the old gas out and it started up after about 10 pulls. Ran a tank through it Saturday cleaning fence rows. Now it will sit and idle all day and starts right up. I dont think this saw has had very much use!

Sent from my SAMSUNG-SM-G891A using Tapatalk

 

[Timberjack zack]

Damn that's a great one you definetly suck lol

Sent from my SM-G930V using Tapatalk

 

[president]

I picked this 026 up last week. Guy said it was hard to pull and had old gas in it. I offered $100 bucks and he took it. Drained the old gas out and it started up after about 10 pulls. Ran a tank through it Saturday cleaning fence rows. Now it will sit and idle all day and starts right up. I dont think this saw has had very much use!

Sent from my SAMSUNG-SM-G891A using Tapatalk

 

[Haywire Haywood]

I can’t believe no one else bid on this or even watched the auction.

Saw that. Couldn't find a bar and sprocket to run it on my 550xp, so I let it go.

 

[JohnMaddux541]

Found a project Johnsered 630 on Facebook and the guy also had this 268, I got both for $200. The 268 would start but I couldn’t keep it running. Dinked around and found all the 268 needed was a tank vent and air filter studs. It came with a cheap Chinese carb so I bought the original Tiltson Carb. I have yet to buy the air filter studs so the saw isn’t complete yet but should be soon. From what I can tell the saw has very little use and for only being $142 bucks in, I think I scored

 

[Brent Adams]

Does this qualify? Found a shop that had a dead saw "pile" or should I say piles. Nastiest saws ive picked up in a while. Filthy.
The 250A just needs a tank vent and maybe a carb kit. Has 150 psi. $15 bucks.
700 is just parts. Only 120 psi, but cyl doesnt look bad. That one was 5 bucks. Good recoil assy, tank, etc.
Power mac 6 was the filthiest, inside and out. Caked full of oil and sawdust. Recoil cover screw threads all stripped out, but has 160 psi and spark! Both it and the poulan ran with a little mix down the throat.
Still havent looked over the 110, but it has the recoil assembly, fuel line, and manual oiler pump parts I need for my mini mac 25, plus a 14" bar and decent chain.
$50.00 in the whole lot.

 

[Brent Adams]

Forgot this one. Got it back in January for $100.00. Has original 18" bar and I believe original chain. Just had to tweak the carb to run right in the wood and do a little "customizing" on the " formerly" low kickback chain. It pulls like a freight train and usually pops on the first or second pull. Had a new carb kit in it when I bought it.

 

[394xp]

Here’s some of my suckage for this year so far, picked up a Husqvarna 555at and 365 x torque paid 250$ for both . Then picked up this chain sharpener, it came with all the stones for all different chain, new in the box stihl .325 chain , two brand new faller wedges..... all for 40 $ . Now my prices are in cad dollar .

 

[Terrence Jefferson]

Picked this one up today for $50.00 has 160 psi compression and is complete just needs a good bath.

 

[LoveChainsaws]

Had a slow afternoon at work so drive about 30 minutes south of my house and stopped at a pawn shop new to me. This immediately caught my eye. Pull rope was broke but they claimed it ran when they took it in. Had a 20” Oregon bar in good shape and 3/8 chain about on its last sharpening but usable. Had tag for $119. I inquired and they pretty quickly said we’ll take $85 plus tax equals $90.10. I don’t think I could have said, “I’ll take it” any faster. Put in the trunk and went home. Rope had only broken at knot on starter pulley. I re-tied, tensioned it up and was back in business. Fuel in it smelled good. I added some bar oil as it was empty. Put choke on, pulled about 10 times and nothing. Primed it at carb throat, nothing. Popped top cover off and checked spark, had spark. Primed the cylinder thru spark plug hole. 3 pulls later and running. Throttles out, idles, oils. Let it cool. Removed muffler and piston and cylinder look perfect!

 

[furb]

Starter won't engage and found coarse thread bolts in the lower muffler holes so someone was in there. Not sure if the cylinder is oem. Too much crap on the bench to mess with it yet. $50

Sent from my iPhone using Tapatalk