Swap meet...

SawGarage · Jul 21, 2010

anywho...

066 brake lever...anyone? I'll trade ya a nice clean ms660 that doesn't fit

i need this to finish my saw!!!....booo hoo...

Teddy.Scout · Jul 21, 2010

SawGarage said:
oh, god...maybe even worse..

I was thinkin Back to the future.. :monkey:

Naw, "Super Bad"

Teddy.Scout · Jul 21, 2010

SawGarage said:
anywho...

066 brake lever...anyone? I'll trade ya a nice clean ms660 that doesn't fit

i need this to finish my saw!!!....booo hoo...

What does it look like?????????

sefh3 · Jul 21, 2010

I'm looking for an intake flange and carb for a Stihl 015. I have parts to trade for.
Still looking for a piston and rings for a Lombard Comango.

fredmc · Jul 21, 2010

sefh3 said:
I'm looking for an intake flange and carb for a Stihl 015. I have parts to trade for.
Still looking for a piston and rings for a Lombard Comango.

I have the 015 stuff you need. Do you have any 036 stuff? 038? 064?

warjohn · Jul 21, 2010

sefh3 said:
I'm looking for an intake flange and carb for a Stihl 015. I have parts to trade for.
Still looking for a piston and rings for a Lombard Comango.

I have a parts 015 that may have what you need. If Fredmc doesn't hook you up PM me and I will take a look.

forestryworks · Jul 21, 2010

updated

forestryworks said:
lookin' for an 044 powerhead. P&C needn't be in good condition as I have an extra.
I'll even eyeball an 046 powerhead with a bad P&C as well.

I got:
361 half wrap, small clutch cover
361 gas tank assembly, stripped handle mounts

066 half wrap, small clutch cover
066 brake handle, half wrap version

440 small clutch cover
440 standard muffler cover

3 or 4 20" b&c in stihl large mount - 3/8ths .050
I would trade these as a set for a 32" or bigger b&c in Stihl large mount.

.

SawGarage · Jul 21, 2010

Teddy.Scout said:
What does it look like?????????

OHH! OHH! I'm heading to I-90 now..

see you in a few hrs. :dizzy:

SawGarage · Jul 22, 2010

SawGarage said:
..it looks like there maybe more than one type. this saw is a bit older, and the late 066/660 one doesn't fit.
(the case seems to high...)

part # is: 1122-792-9101

the '792' could be a '798'...not sure..

Teddy- looks like this: i can get a better pic tomorrow, if need be.

where the handle enters the case, it seems the distance from the pivot point to the top of the notch that fits behind the plastic cover is not TALL enough on the 'handle' i have now.

Forestryworks - i didn't know they had one for std or wrap bars....interesting!

stihlman32 · Jul 22, 2010

Still looking for an 036 cylinder or 34 Super cylinder. Got green to trade. PM if you can help.

forestryworks · Jul 23, 2010

updated

Looking for:
an 044 powerhead. P&C needn't be in good condition as I have an extra.
an 046 powerhead with a bad P&C as well.
91 driver chains in full comp or semi skip, round grind.
32" bar, stihl mount.

I got:
361 half wrap, small clutch cover
361 gas tank/rear handle assembly, stripped handle mounts

066 half wrap, small clutch cover
066 brake handle, half wrap version

440 small clutch cover
440 standard muffler cover
440 Max Flow air filter, opened but not used

SawGarage · Jul 23, 2010

SawGarage said:
Teddy- looks like this: i can get a better pic tomorrow, if need be.

where the handle enters the case, it seems the distance from the pivot point to the top of the notch that fits behind the plastic cover is not TALL enough on the 'handle' i have now.

Forestryworks - i didn't know they had one for std or wrap bars....interesting!

Part#:

SkippyKtm · Jul 23, 2010

Still looking for a Echo 610EVL ("the twin") CDI module have green to trade. PM me if you have one. Thanks. :cheers:

smilin possum · Jul 23, 2010

looking for a longer bar for a DA211 Mercury all I can get between the trans and helper handle is 38" want to go bigger, and the old style rubber handle for the cranking rope. May have some trade or I got green.

fredmc · Jul 23, 2010

Anyone got a ducati coil for a 109,111,110,115 dolmar? can trade or buy

fredmc · Jul 23, 2010

I can also get some 064 parts. (pretty much the whole saw):greenchainsaw:

SawGarage · Jul 23, 2010

fredmc said:
Anyone got a ducati coil for a 109,111,110,115 dolmar? can trade or buy

will a Ducati coil for a 750ss or 900ss, or a 996 Superbike work? :monkey: :spam: lol...

fredmc said:
I can also get some 064 parts. (pretty much the whole saw):greenchainsaw:

interested in some parts... PM sent..

J

Kwdog75 · Jul 23, 2010

fredmc said:
I can also get some 064 parts. (pretty much the whole saw):greenchainsaw:

How much for the whole 064?

cat-face timber · Jul 23, 2010

Looking to trade a Mac 10-10 Right hand start crank assembly that needs work, for a 048 AV air filter with all the flocking

Can send pics of the Mac part.

Thanks

parrisw · Jul 23, 2010

I need 372 parts? anybody? anybody? starter cover, clutch cover side tensioner, 50mm piston.

Swap meet...

Help Support Arborist Forum:

Addicted to ArboristSite

Teddy.Scout

Guest

Teddy.Scout

Guest

Addicted to ArboristSite

Addicted to ArboristSite

Addicted to ArboristSite

Addicted to ArboristSite

Addicted to ArboristSite

Addicted to ArboristSite

ArboristSite Operative

Addicted to ArboristSite

Addicted to ArboristSite

The Lorax, my FIL rip...

Addicted to ArboristSite

Addicted to ArboristSite

Addicted to ArboristSite

Addicted to ArboristSite

Addicted to ArboristSite

Knot Bumper

Tree Freak

Similar threads

Join the conversation!

Join today and get all the highlights of this community direct to your inbox. It's FREE!