Swap meet...

[Jacob J.]

Might want to check with Jasha. Last I heard he was getting rid of all his 660s, that was awhile ago though.

Yeah Sling'r likes the 385/390s...

 

[Kwdog75]

Looking for a heated 372 xpg full wrap handlebar.

 

[upstateny]

Crankcases, cylinder, small parts galore for the 372. No gas tanks Two full wrap handlebars that have been hit by the chain quite a few times but still hanging in there.

Rupe, could you PM me some more info on this? 372 lost the battle with rear tire on a 640 John Deere the end of last week.

 

[Lunchbox]

Dolmar coil

Found the list of coils that will fit the dolmar ps6000i i need a coil for.
116si
120si
6000i
6800i

if you have one i,m sure i could come up with something
tnx.

 

[Saw Dr.]

Rupe, could you PM me some more info on this? 372 lost the battle with rear tire on a 640 John Deere the end of last week.

I have some parts around if Mike cannot help you. post up some pics in the main forum. You never know what may turn up there.

 

[Jack_Shaft]

I need a Stihl 009 coil, wire & cap.

It seems my saw has had an electrical failure... anybody have a good working coil to try?

 

[Urbicide]

Looking for a heated 372 xpg full wrap handlebar.

I may be mistaken, but I don't believe that Husky offered a full wrap heated handlebar.

 

[jeepyfz450]

Im looking for a plug wire and belt for a homelite 26 lcs.

 

[Kwdog75]

I may be mistaken, but I don't believe that Husky offered a full wrap heated handlebar.

Ahh crap, a heated half wrap would be appreciated. I found a full wrap heated handlebar for a 394 so i thought they made the same for the 372, my bad!

 

[rupedoggy]

I have some parts around if Mike cannot help you. post up some pics in the main forum. You never know what may turn up there.

I sold most of my stuff but still have a top plastic (large not small) for him for shipping but can you help otherwise? Mike

 

[stihlboy]

i need 084 parts!!!!

 

[Jacob J.]

Ahh crap, a heated half wrap would be appreciated. I found a full wrap heated handlebar for a 394 so i thought they made the same for the 372, my bad!

There was a heated full wrap available for 372. 503 62 86-99 was the part number. I bought two of them new from Bryce. I got a deal on them @ $75 each since they listed for $181.60 at the dealer. I'll bet you can NOS out there somewhere.

 

[Saw Dr.]

I sold most of my stuff but still have a top plastic (large not small) for him for shipping but can you help otherwise? Mike

Yes, and I will if he will post up some pics or a list of what he needs. I don't have any 50mm jugs I want to part with, but I have a fair amount of other stuff. I don't have any high top plastic either, so this might work out well for him.

 

[Brushwacker]

I need a Stihl 009 coil, wire & cap.

It seems my saw has had an electrical failure... anybody have a good working coil to try?

Had, just put all my 009 stuff on ebay tonight in parts lots. If 1 don't sell 1 will have 1 in a week. This year so far a lot of items haven't been selling.

 

[SawGarage]

hey guys... i need a brake lever for a 066...it looks like there maybe more than one type. this saw is a bit older, and the late 066/660 one doesn't fit.
(the case seems to high...)


part # is: 1122-792-9101

the '792' could be a '798'...not sure..


plenty of parts...but green may be easier.



Also, i need a (don't laugh, or flame...it's for a friend...) a carb/cyl plate/bulkhead piece for a 137 husky...

DO NOT know what happened there, but a TERRIBLE air leak behind the carb... saw is almost new.

also need a clutch cover/chain brake assembly for a 625, 630, 670 j-red


still looki for the 066/h137 parts...

.

 

[wigglesworth]

Anybody have any interest in this ol' torquer? Great comp, starts easy and runs great. Pretty good lookin as well.

Im into 026's, 044's and $$$

 

[PogoInTheWoods]

Anybody have any interest in this ol' torquer? Great comp, starts easy and runs great. Pretty good lookin as well.

Im into 026's, 044's and $$$

I just acquired a basket case version that needs mucho help. Not sure if I even want to go there yet, but....

Have any leftover parts from getting yours revived?

Poge

 

[upstateny]

I have some parts around if Mike cannot help you. post up some pics in the main forum. You never know what may turn up there.

I sold most of my stuff but still have a top plastic (large not small) for him for shipping but can you help otherwise? Mike

Yes, and I will if he will post up some pics or a list of what he needs. I don't have any 50mm jugs I want to part with, but I have a fair amount of other stuff. I don't have any high top plastic either, so this might work out well for him.

I posted up some pics in the Chainsaw forum. The saw really isnt that bad off. Mostly just cosmetics. I'm not worried bout looks...its a work saw...gets thrown in the truck, skidder, etc.

http://www.arboristsite.com/showthread.php?t=142753

 

[wigglesworth]

I just acquired a basket case version that needs mucho help. Not sure if I even want to go there yet, but....

Have any leftover parts from getting yours revived?

Poge

No left overs. No reviving on this one either, it was a runner when I picked it up.

 

[oscar4883]

Anyone have a handle for a 290/310/390? Looking for a clean one if possible.
Thanks
John