husqvarna

Anyone feel like chiming in here about any tricks to get this back together? The mechanism is extremely stiff and I can’t get the brake to pivot as soon as I put the cam pin in. I’ve searched for videos online and found one about a 55 but it’s not the same. This is a circa 89/90 era saw. I had...

Hi guys, I saw yesterday on FB that Patrick Lacey had an unfortunate run in with a dirty rotten snag on the job and is currently laid up. From the sound of it it was pretty bad. He is not looking for donations so I figured I would take a cue from his buddy that posted on FB and try to get as...

Clean Husqvarna 254xp, Runs good. Piston and cyl are clean. Comes with bar and chain pictured. Saw is NJ for pickup or can ship pretty reasonably. Asking $400

Maybe keep engine cooler n combusting better. I know most cutters live in a cooler climate. But in a hot environment? How can extra cooling be a bad thing. Especially on a completely closed air box, with an engine I expect to perform n create heat. I might go a bit bigger hole n line the...

Title pretty much sums it up and I've done the research on HOW to do it. Still probably going to get stuck lol. I was wondering who out of you have handled a ported 346xp, I mean out of the box the engines rpms mac out at 14,500 which is already insane. Curious on your thoughts on the project...

New crank bearings, gaskets, seals, oem piston, rings. Runs and oils as it should. It does have some blemishes but should be a good runner. Would like $375.00 shipped to you.

Hey guys. I'm Matt. I've been working for a trail crew in Utah and enjoy the saw work immensely. It has given me the spark to finally try to get this saw running. I got it for free from a ski resort firewood crew and was told main bearing was bad. The further I got into the saw the more problems...

This one has new skf bearings, oem piston & ring, gaskets, and fuel line. There is one hole that i repaired with a time-sert. As you can see the muffler is getting thin and there is a crack in clutch cover. This saw has not been in wood yet. Would like $425 shipped.

Yes another 385xp! This one has new Meteor piston & rings. Pull rope & steel insert along with carb kit. This one has been started, warmed, adjusted and rpms checked. Setting are set rich at this time. Havent had in any wood yet. There are some signs of wear as this is not a NOS saw! Anyway will...

Hello all, I'm new here so my apologies if this isn't in the correct spot. My question is what a good condition husky 365 is worth? I don't think it's a special but I'm not sure because the sticker was removed. Thanks

Just trying to thin the hurd. Saw has new oem piston and rings, carb kit. AM cover and tank. Saw is not a shelf queen but is still a good running saw. Put a tank of fuel through it after piston install. $325.00 shipped

Forsale PHO. Saw has one tank on new rings. There is some scrapes and bruises as you can see. Some retard thought he needed to scratch his initials on clutch cover. Can swap full wrap for half if wanted. Asking $435 and ill pay for shipping.

Saw has carb kit, new piston rings and top cover. Has about a tank of fuel since repairs. Muffler is dinged up a bit. Selling as PHO! Will cover shipping to lower 48. Would like to get $450.00. Will swap out full wrap for half if wanted. Just added piston pic!

HI all, first post for me here although been lurking for some time. I have a very low hours 480CD that I use for occasional milling- mostly canting larger trees in the woods that i cant get my bandsaw too. I have basic knowledge of porting 2 stroke engines- mostly high performance...

Hello all, new user to the site, have lurked some forums. What a great place. Lots of helpful advice and tips. Little back ground. Husqvarna 254 professional serial number 8180663, I seem to have a dead coil. Saw is ancient but I love it. It rips! Compression check 130 psi cold 145ish...

Hey everyone I'm new here. I have a husqy 435 that I have almost decided to set on fire. I never could get it running right. It had odd intermittent starting issues usually when hot, then all together. I tried all the usual suspects. Put a new carb on, new vent filter, new fuel filter, new spark...

I have a husqvarna 365, bought new this year. I have been milling slabs with it using an oregon 28" bar, trying various brand ripping chains. I have some great timber that is too big for the 28" setup (max cut width ~23"). Will my 365 be able to run a 32" bar and chain (max cut ~26-27") with...

Does anyone have a detailed picture or diagram of a husqvarna 36 carb and how it is installed? Mine is apart and I cant remember how to put it back together. Specifically the choke and throttle levers on the right side. Cant figure out how the spring and stuff goes back with the choke lever...

The impulse grommet on my Rancher 55 is worn beyond use. I live in Chile and the local dealer does not have the part unless I also buy a new cylinder (at a ridiculously high price). A new one from the States costs about $7, but the shipping is about $35 and import duties add some more. I can...

Husqvarna 455 Rancher. Starts,runs,cuts as it should. $285 shipped in lower 48. Compression 150 psi.Powerhead only in shipped price. Bar and chain can be negotiated in deal. Make me an offer.