husqvarna

Newby and thanks for allowing me to join. I have a 455 Rancher that I was using and just as I finished cutting thru log it died and will not start. I have checked for spark it's good, new plug and flywheel key is good, checked gap for coil seems fine, poured gas in spark hole and still nothing...

Newby and thanks for allowing me to join. I have a 455 Rancher that I was using and just as I finished cutting thru log it died and will not start. I have checked for spark it's good, new plug and flywheel key is good, checked gap for coil seems fine, poured gas in spark hole and still nothing...

Looking for a decent Husqvarna 394 starter/recoil cover. In working order preferred. Rope condition not crucial.

I recently rebuilt a 242xpg. It was not splitted. Only cylinder/piston inspection, and new gaskets. Its in great shape. At first startup it was acting like it has a vacuum leak. After firing It started idling higher and higher, and it would die when i used the throttle too much. Turning the...

So my buddy smoked this saw originally by running straight gas in it (like a dummy) and blew up the crank bearings and part of the bottom of the piston. He got a quote for a repair and which made him *pucker*, so then he just gave it to me because I love tearing things apart. So I pulled it...

Hey guys, it's been a while since I've posted here, but I'm back! I've acquired a 1997 365xp from my In-laws for $200. It's in rough shape but I thought it's the perfect saw to finally experiment on and do a full port job. I'm hoping some of you more experienced porters can chime in and give...

Very nice 372xp oe @Duce built saw with maybe 2 tanks run on it. Got it in April and have since added brand new oem low top cover and oem side cover. two sets of felling spikes as well. large and standard size. large are oem and standard are aftermarket. Price is $500 plus shipping, Shipping...

Hey fellas, I opened up my new 445e muffler a little bit (drilled Two 1/4 inch holes and removed spark arrestor) I have the tool to adjust the carb. I believe I have it four stroking and it cleans up well in the cut. After a few hard hours the plug looks pretty lean, if I back the H screw out...

I bought a 565 today and while looking it over i noticed quiet a large crack in the intake boot. Hope you can see the crack in the photos, how many of you have seen this on brand new saws?

I bought a 565 today and while looking it over i noticed quiet a large crack in the intake boot. Hope you can see the crack in the photos, how many of you have seen this on brand new saws?

This is the second time this has happened to me on this saw. The first time my dad put straight gas in it. It looks similar and I used acid and sandpaper to clean the inside of the cylinder and just added a new piston. It wasn't perfect but it looked pretty good. I am wondering if this...

As a newb, I’m insanely confused with all of the “oil” options out there. I have a Husky 440. As for fuel, I’ve been using a store bought pre-mix (I’m ordering Husky brand pre-mix just to be safe). I recently bought Husky brand bar and chain oil. HOWEVER, the small print on the back scared...

FS Jonsered 2253 with the MMWS treatment. The saw has less than 1 hr of runtime according to the dealer who updated the carb software in Sping 2019.if you’re not aware of this model it’s identical to the 550xp MK1 but just in red. $750 Shipped Paypal F&F to your door if you live in EST, CST, or...

I just closed a deal for €110 for a second hand husqvarna 372XPG. Is it easy to work on? It looks like it's been neglected for the past few years, probably needs some attention. I know how to do th basic things to a saw, carb, spark plug, cleaning muffler etc... Any tips? Thanks in advance, Jan

2004 Husqvarna 55 Rancher, big loss of power in cut, RPMs drop. Chain sharp, tension adjusted. Fresh fuel. No smoke. Figured I had the carb. mixture mis-adjusted, I riched out the H screw a little at a time to about 2 turns out from seated. I removed mixture screw limiters a couple carb...

I am interested in making my own base gaskets for a couple of Husky 350's that I am rebuilding. What would be an appropriate gasket material for that? Thanks in advance!

I have spark, I have fuel. I have 130lbs compression with just 3 pulls. I have gapped and I regapped and regapped the coil/flywheel... Mind you, I have good blue spark when I put the plug in the boot and ground it on the cylinder head. Put the plug back in and try to start it I get nothing. I...

Anyone feel like chiming in here about any tricks to get this back together? The mechanism is extremely stiff and I can’t get the brake to pivot as soon as I put the cam pin in. I’ve searched for videos online and found one about a 55 but it’s not the same. This is a circa 89/90 era saw. I had...

Hi guys, I saw yesterday on FB that Patrick Lacey had an unfortunate run in with a dirty rotten snag on the job and is currently laid up. From the sound of it it was pretty bad. He is not looking for donations so I figured I would take a cue from his buddy that posted on FB and try to get as...

Clean Husqvarna 254xp, Runs good. Piston and cyl are clean. Comes with bar and chain pictured. Saw is NJ for pickup or can ship pretty reasonably. Asking $400