stihl

I Am a teenager who acquired an abandoned Poulan wild thing and will soon buy an MS 194C. Ethier gonna buy Stihl function chaps or Clogger Defender Pro full calf wrap chaps.

I have an 066 chainsaw for sale, with TONS of extras. 4 bars, 3 brand new and 1 used. The bars are as follows; 1x36" 1x28" 1x20(new) 1x20"(used) 12 brand new chains--Assorted for ALL OF THE BARS. Files Sqrench New carb, air filter, spark plug, ignition module, fuel filter. Asking 1900.00 for all...

I have an 066 chainsaw for sale, with TONS of extras. 4 bars, 3 brand new and 1 used. The bars are as follows; 1x36" 1x28" 1x20(new) 1x20"(used) 12 brand new chains--Assorted for ALL OF THE BARS. Files Sqrench New carb, air filter, spark plug, ignition module, fuel filter. Asking 1900.00...

.

Needs work. Broken AV pin on the tankhandle upfront underneath. It can be fixed. Stripped upper cylinder AV spring hole mount. Now fixed Side AV rubber hammered. See pics. Runs, no serious damage to it so it can be fixed up. Pumps oil starts fine. Sale as is. It's complete minus the broken...

Been picking away at this job when it hasn’t been terrible weather. Cutting for a Danish customer that had a summer house in my area. 20+ trees between 12-24 inches came down. Logs cut to 3.1m. At first he wanted me to ring it up in 30cm (1 foot) rounds and then he was going to move it all to...

Hello and thanks in advance for any help given. Thinking of moving some saws to make room for new. I have a nice stihl 038 magnum 72cc Brazil made early 1990s vintage with a new stihl 25" es bar and chain. If I decide to sell what would a good asking price be? Also have a nice husqvarna 268xp...

I just bought a nice pro mac 55 and was wondering something The saw currently has a Walbro SDC single jet carb (not sure if I am using the term correctly). It has an idle screw and a low jet screw. Seems to run nicely. I have another SDC carb with double jets (idle L and H). Should I swap the...

pics of full size images on page two. If you would like the soft starter handle it's here with the original rope on it although a bit dirty and worn some. This rope is new with used OE pull handle. Enjoy I know, bla bla bla but I'm not logged in on my phone. This tool is low hours from the...

Does anyone have any leads on one of these beauties! Can’t seem to find one here in my area.

MS461 chainsaw, this is how I received the saw and has been picked apart, what you see is what you get, crank seems ok, case doesn’t look bad but does have a chip missing from front case, tank doesn’t leak but does have some damage, wrap handle seems bent, flywheel is missing a fin. Asking 125...

I am wanting to convert my 372 high top (HD filter) to low top. I bought the following parts to do the swap: COVER 503 62 80-01 HOLDER 503 62 75-01 AIR FILTER 5114550-01 Question is, after ompleting the swap, will I need to adjust the carb ? If so what might need changing, low jet, high jet...

First saw of my own, I’m hooked and ready to get more! I’ve cut a little with it but can’t wait to really put her to work! Love these 1127 series saws! These babies are tanks!

Hello everyone! Just recently bought my first saw of my very own, a very well maintained MS 310 w/ 20”bar. My father in law owns 100 acres with about half of that in woods so trees are constantly needing trimmed and cleaned up. He’s running a 290 and a 170. Would like to buy a lightweight limber...

I've heard Stihl discontinued the MS880 chainsaw for emissions-compliance reasons and replaced it with the MS881. Supposedly it has the same HP and CC's. However, the MS880 was rated to pull a 59" bar, and the new version, the MS881 is only rated for a 41" bar. Does anyone know why they de-rated...

All the usual suspects, take-offs, broken or that your done with now. Any 1124 or any large saw parts for Stihl will be considered. 075/760, 105s, 050, 051, TS510, 070, 090, ect... If you have an add here listed I've seen it already. Plastics Starters and parts Clutch covers Oil pumps working or...

I have a Homelite XL-924 that I can’t get to idle and keep running! Here is what I know: -It has spark + brand new spark plug adjusted with the correct gap -145 psi -Exhaust baffle has been grinded and is free of any build up -Brand new fuel lines. Carb is pulling gas. Running 32:1...

If this is not the proper forum please forgive me and maybe someone can move it to the proper location. Need a brush cutter for briars and brambles and tall grass, and minimal trees - maybe occasionally 1 inch. Unread somewhere 240 is 2 stroke and the R model is the valved engine. I have an old...

Will I increase the performance of my saw if I enlarge the factory exhaust hole? I was thinking of doing it with a die grinder. Will my saw burn out? How big should I go? Has anyone done this before? Is too much too much ? I already have a West coast saw bark box on it Cheers

I was thinking about STICK WELDING a west coast saw exhaust port on a MS 461 muffler. Will the exhaust handle the heat from the welding? What do I need to use as equipment? Has anyone done this before ? Cheers!