Dolmar PS420 after some use
- Thread starter cuttinscott
- Start date
Help Support Arborist Forum:
cuttinscott
Addicted to ArboristSite
I got puzzled by the same thing.........opcorn:
Steve Was Showing How easy and how little effort the saw would start with. If you pay attention he would shut the saw off after every start.....
Scott
I like that new kill switch ......
SawTroll
Information Collector
Well, I admit I suspected that - but didn't have the sound turned on while watching.
It sure looks neat, but then again there is the weight penalty.......:biggrinbounce2:
If the Stihl published weights are any indication, that fancy starter accounts for most of the excess mass.
MS180 adds 0.5lb, MS210 adds 0.9lb with chain adjuster knob.
MS180 adds 0.5lb, MS210 adds 0.9lb with chain adjuster knob.
Oh yeah!. Just a little bump, it dies, and the switch springs right back up.
2000ssm6
Stihl User
I never seen a saw start so easy.........
Edge & Engine
ArboristSite.com Sponsor
I just measured my PS-350's compression (has less than half a tank through it). 195psi also. It's incredible, you'd never know that compression was that high just by pulling it.
166
Addicted to ArboristSite
Here's some detailed pictures from an earlier thread last fall.
Dolmar ps420 sighting.....
http://www.arboristsite.com/showthread.php?t=75654&page=5
Dolmar ps420 sighting.....
http://www.arboristsite.com/showthread.php?t=75654&page=5
Last edited:
166
Addicted to ArboristSite
166
Addicted to ArboristSite
166
Addicted to ArboristSite
]
166
Addicted to ArboristSite
windthrown
361 Junkie
Dagnabbit! You are making my bad case of CAD even worse posting photos like that on this site! :bang: :bang: :bang:
K9-Handler
ArboristSite Operative
This man obviously has no sense of humor...
IT WAS A JOKE, SCOTT!!!
:hmm3grin2orange:
Last edited:
anynamewilldo
ArboristSite Lurker
hows the 510?
Hows the 510 stack up with the 420? I know its heavier but over all?
Hows the 510 stack up with the 420? I know its heavier but over all?
This next shot is with the outer cover re-installed over the screen shell on the sa
I just wanted to expand on 04Ultra's muffler pics above. He had mentioned before about drilling out the two welds, but couldn't quite picture it until he posted the photos -- then it all made sense!
I have a ps420c to as well ps32c and a small ps221 ad a mac xtreme 3.4 , ps221 is made in japan and the mccullough it is made in itali bi Husqvarna thei stop the prodaction and close the factori...i did myfler mode to ps42c and ps32c bat i did not open the hi end yet what is the gain in hp? and if someone have ani opinion on the mac...it will bi aprisieted
Last edited:
exSW
ArboristSite Guru
Wow,and I thought I just bought a chainsaw.Turns out I bought a trans-atlantic,multi-year debate.After nearly two gallon of gas through it since April 14th when I bought it I'm pretty happy with my 420.
I have a dolmar ps420c to as well ps32c and a small ps221 ad a mac xtreme 3.4 , ps221 is made in japan and the mccullough it is made in itali bi Husqvarna thei stop the prodaction and close the factori...thei make the new macs i sweden now...i did muffler mode to ps42c and ps32c ... i did not open the hi end yet what is the gain in hp? and if someone have ani opinion on the mac...it will bi aprisieted:confused2:
Last edited:
Sory i did not see the date....:msp_smile:
