I wouldn't be much help on that. Sorry. Not torn into one of those yet.
Homelite Chainsaws
- Thread starter briantutt
- Start date
Help Support Arborist Forum:
kshansen
ArboristSite Operative
Well I like the looks of this one! If it's for $20 I'll take it! Let me know your preferred payment method, I have had good luck using PayPal. Just need you email address to send you the $20.
It does not interface with the reed block as it comes out through the tiny hole circled in blue in one of my photos. I call that the carb throat and someone else called that the venturi. That doesn't matter. What matters is the large hole is connected to the tiny hole. No filtration is there to block debris or contaminates. If anything should happen to enter the large hole, it would probably clog the exit hole.
I am not having any issues. I just rebuilt the carb and want to make sure I won't have any. The carb is off of a 1977 Homelite Super XL925 which is in pristine condition. Very little use. Extremely dirty as original owner was using used motor oil for chain lube. It now belongs to a friend and I am cleaning it up for him. Rebuilt the carb, replacing the fuel lines as the ones in it now are like concrete, etc. . I feel certain it will run as it has great compression, great blue spark, etc. It just needs a little tender loving care and should be back on line soon. Thanks for your reply. OT
Thank you Bob,
OT
I see. here's the same hole in my carb from when I had it apart. I don't think mine had a passage open into the intake. same carb, same saw.
Attachments
found another picture . looks like a small plug is in there.
here is similar Tillotson carb from my Jonsereds 90.
I put a small amount of dye into the large hole and put pressure on it with my mityvac and the dye came out the little hole I have circled in blue. Not sure what carb you have. All I know is that on mine, they are connected. Thanks for your continued interest. OT
Looks exactly like mine but there is no plug. I think that is just the casting. Wish you still had it off. lol Then we would know for sure. Thanks again. OT
sounds like you have pitting or a poor casting. Plug it with silicone, let it cure and try it out. if it works well, fill it with JB weld. there is no way they made that to just suck air and debris into the carb.
looking at my pics again, I don't think that there's a plug in there, just casting.
There is no pitting. Trust me, it is cast that way. I can see the hole leading to the carb throat. That's why I put a drop of dye in it and used the mityvac with pressure. Dye came out the tiny hole circled in blue in my pic. OT
got about 40 homies here. dont use them any more.
Chainsaw Collectors
ArboristSite Guru
Nice. Are you saying that you would be willing to sell them?
and it's a 151B carb? dunno then.There is no pitting. Trust me, it is cast that way. I can see the hole leading to the carb throat. That's why I put a drop of dye in it and used the mityvac with pressure. Dye came out the tiny hole circled in blue in my pic. OT
I haven't worked on that model Tillotson carb or that kind of saw but i wonder is there any chance the original carb was replaced with another model / variant Tillotson that was actually not the correct carb for that saw at some point?
In that post, there are two different saws. Only had one intact plastic piece. The other was broken. I assume you are referring to the nicer looking one. I can pair it with the good plastic piece.
thinking about this, it really doesn't make any difference. the whole compartment for the carb is under this filter. if you're worried about that small hole taking air and dust into the carb throat, the entire carb inlet is sucking in massive amounts of that same air/dust like a vacuum.
kshansen
ArboristSite Operative
The piece I really need is the one you have in your hand off the saw. If you want to send me the better looking saw that would be fine.
I think it would be best if we exchanged the shipping addresses via email. My email address is [email protected]
Gotcha. That makes more sense. It makes zero difference to me. I will send whatever you want. I don't mess with emails much but I'll get it figured out. I think the one the wife has got me is- [email protected]
The $20 I mentioned was what it cost to ship a whole saw the last time I sent one that way. I'm sure if you just want the piece/ pieces, it would be less.
The $20 I mentioned was what it cost to ship a whole saw the last time I sent one that way. I'm sure if you just want the piece/ pieces, it would be less.
