Homelite Chainsaws

[xl130]

Got the bar and chain sorted

 

[Piotr Pakuła]

Is the SXL-925 piston available?

 

[cbfarmall]

Only aftermarket unless you get lucky. I'd check that cylinder first. That's one hell of a gouge over the ring.

 

[Piotr Pakuła]

Yes, you are right, first I need to look at the cylinder, I found an Lrb piston or I can try to convert the piston to thicker rings. Then I would buy 52.5mm metric rings

 

[Piotr Pakuła]

Is this 2 part filter correct? Is this some kind of modification

 

[Piotr Pakuła]

Someone must have modified the chain tensioner

 

[moxiemaul]

Bar adjust looks the same as on my SuperXL Auto. What part are you thinking is modified?

 

[Piotr Pakuła]

Bar adjust looks the same as on my SuperXL Auto. What part are you thinking is modified?

The guide I received is a converted Chinese 24"

 

[Piotr Pakuła]

Piston sxl-925 / 32€ / Closer to me
https://agroparts.gr/p/piston-kit-for-homelite-super-xl-925-52-38mm/

 

[Piotr Pakuła]

Is this 2 part filter correct? Is this some kind of modification

I suspect that it is an additional pre-filter that also seals the outer edge. Thanks to this, the filter is as good as new

 

[cbfarmall]

Is this 2 part filter correct? Is this some kind of modification

More like 2 different filters stacked one on the other--OEM and aftermarket. Never seen 2 flat filters stacked like that on any saw.

 

[Piotr Pakuła]

More like 2 different filters stacked one on the other--OEM and aftermarket. Never seen 2 flat filters stacked like that on any saw.

The black one is clogged

 

[Yukon Stihl]

A 26 LCS question
I got a seal for the flywheel side that was leaking and installed it.
Then I pressure tested again and found a hole in the crankcase that leaked under pressure. It is on the edge close to the belt case.
Is this a case where it’s supposed to be open ? The parts saw I have has a casting mark but no hole
Thanks

 

[cbfarmall]

Here's my 26. The only port I know of is for the tank pressure line. Maybe your case came off something else.

 

[cbfarmall]

My Super 2100. Put a 7 spline drum on it, has a 7/8" clutch. Helper handle just because I could.

 

[Piotr Pakuła]

My Super 2100. Put a 7 spline drum on it, has a 7/8" clutch. Helper handle just because I could.

View attachment 1240151

What does a 7/8" clutch look like?

 

[cbfarmall]

I don't have a picture but it's like any other Homelite 6 shoe clutch with 2 garter springs, but the widest they ever made. Standard 2100 clutch is 3/4" wide. My saw also has the matching sandcast clutch cover that goes with the clutch and the wider full wrap. It's an impressive looking clutch and heavy.

 

[cbfarmall]

Assembled to the saw.

 

[buzz sawyer]

Assembled to the saw.

View attachment 1240195

Didn't know they made a 7/8, but I never saw the ipl for the 2100. My 1050 has a 3/4.

 

[Jay Hansen]

A 26 LCS question
I got a seal for the flywheel side that was leaking and installed it.
Then I pressure tested again and found a hole in the crankcase that leaked under pressure. It is on the edge close to the belt case.
Is this a case where it’s supposed to be open ? The parts saw I have has a casting mark but no hole
Thanks

I thought I had gotten back to you on this, but I can't find my post, so I probably messed it up somehow.
Anyway my 26 does have that hole in the case, and it appears to go clear to the crankshaft. My saw turns over with compression, but it's missing some pieces, so I've never tried to start it. It looks, however, as if it was used with that hole open; there is no provision for plugging it.