Let's see some Christmas giving

[blsnelling]

I've got a tach ( senDEC sts-5000 ) first pm takes it and i'll cover the shipping so its free

That'll make a nice little present for somebody. Someone's always looking for a tach.

 

[little possum]

Thanks ghitch. :yourock:

 

[smitty299]

I've got a tach ( senDEC sts-5000 ) first pm takes it and i'll cover the shipping so its free

B200Driver takes it

 

[chainsawwhisperer]

I've got a tach ( senDEC sts-5000 ) first pm takes it and i'll cover the shipping so its free

Wow! There's a nice gift!!

 

[joecool85]

I have a Craftsmen/Poulan XXV bar and chain. 14 inch.
Will fit other models too.

PM Sent!

 

[litefoot]

That'll make a nice little present for somebody. Someone's always looking for a tach.

+1, Wish I had seen it sooner.

 

[sefh3]

Yeah I was a tad late on that one too.

 

[Fastcast]

Have quite a few Poulan 306a parts.....Need a jug, piston & rings for a FS/55 strimmer....Sure would like to find a "needs a little work" Poulan 4000 on the cheap!

 

[GM_DaddyMac]

Lombard (XL 12)

This is cool idea. Seems like all the saw elves are busy filling Christmas wish lists.

I have a Lombard that I have been told is a re-badged Homelite XL-12. I have not done much with it since I bought as part of a large saw lot. It appears to be complete -- covers, carb, handle, coil, flywheel, etc.

The recoil is not working so I cannot get a compression reading, but the one time I got it to engage, it did pull over (not frozen).

I have seen a lot of buzz about the XL-12 in this thread so thought I would offer for free to a fellow AS member willing to cover shipping cost from 48085. I have enough saw projects for now and this is near the bottom of the list. So, have at it!

PM me if interested.

Merry Christmas!

 

[Wildman1024]

Dayton 2Z463

I got this dayton, its been a headache for me. It runs and really good but when turned on its site it runs faster or slower (Bad Seals). I just got a kit off the bay and replaced the flywheel side and it made it better but not 100% better. It also has a new nova module on it and all new intake gaskets/fuel lines and filter. I have the clutch side seal here but not the tools or the ambition. I'm just gonna offer it up for someone.

I would be interested in a stihl of about the same size or a 6401. Not to picky and will consider what santa has.

 

[teacherman]

I've got a number of cylinders that could use a home-

Homelite 750/8800 (I think it's the same for both, it's 54mm and new) now spoken for also!

Stihl 044 (used, later style- in good condition, 50mm)- is spoken for now

Jonsered 625/630 (same as above, 48mm)Jonsered cylinders now spoken for.

I've got a bunch of flywheels too.

I'll dig around and see what other engine parts I have.

Do you have any 012 cylinders? Just curious........

 

[Jacob J.]

Do you have any 012 cylinders? Just curious........

Nope, I'm happy to say I don't have anything at all for that series of saws (009,010,011,012). I gave the last of it away to another member.

 

[plumbcrazyjr]

i have a cylinder off a ms660 that has a bad scratch between the transfer on the exhaust side no longer have the saw so if someone thinks they can use it they can have it i will even cover shipping

 

[plumbcrazyjr]

cylinder gone that was quick

 

[Garden Of Eden]

Still got a bunch of parts, (2 complete saws minus pistons) for craftsman 2.0s. Little micro buggers. PM with what ya need, and for shipping it's yours. Or, if I can get piston/s, I'll rebuild them/it, and send that. just for shipping.

I'll post a pic of what I'm talking about.

Also, still looking for a decent tach. Will trade/pay. Thanks

God Bless

Jeff

 

[m44]

If anyone has them I need a super Xl p and c a super ez p and c, and a 272 clutch cover. I have tons of parts for homelite xl-2s if anybody needs them.

 

[MotorSeven]

Brian VT, I read you were looking for 020 parts...what do you need?

I have a entire crank/bottom end, a cylinder that needs very little work & I can even throw in the scored piston that came with it ;>!

Shipping is on you, just let me know!

RD

 

[Donley]

I have some 041/041AV parts. Post what you need.

I need the aluminum plate that the choke lever mounts to. i am waiting on my dealer to get me all the gaskets from the cyl up so this would be a good time to swap it out if you have one. btw its a farmboss if it matters.

thx in advance.

pss im still looking at this 55 with confused looks. lol

 

[blsnelling]

Those are cute little saws, Jeff. I assume that's a reed saw?

 

[litefoot]

Here at Christmas time, I'd like to make a donation to Darin and Jennifer for maintaining this great site. Can one of you site sponsors clue us in on how to do so?