Let's see your husqvarna

[SawTroll]

.




,

The "G" went MIA wsomewhere....:msp_sneaky:

 

[Mastermind]

 

[JakeG]

 

[brokenbudget]

looks like you took a fiskars to it:hmm3grin2orange:
couldn't blame you one bit!

 

[Eccentric]

Piecing together a 288 low top from a box of parts

That looks familiar. I'm putting a 288XP together from two partial saws as well.

What saw did that crankcase/tank setup come from? The throttle arm looks different than what's on my 288's.

 

[Mastermind]

That looks familiar. I'm putting a 288XP together from two partial saws as well.

What saw did that crankcase/tank setup come from? The throttle arm looks different than what's on my 288's.

Differences of early and later.......one has the lever type and the other uses a throttle rod.

 

[Eccentric]

Differences of early and later.......one has the lever type and the other uses a throttle rod.

Interesting. Mine have the lever that's shaped roughly like that one......but a bit longer and with a 'half-moon' cutout on the underside near the end to bear on the roller on the carb arm.

 

[srcarr52]

Differences of early and later.......one has the lever type and the other uses a throttle rod.

181's came with the wire throttle rod, 281/288's came with the lever/roller setup.

 

[Mastermind]

181's came with the wire throttle rod, 281/288's came with the lever/roller setup.

Thanks for the correction Shawn. I guess I've seen "Frankensaws" that were are sorts of ways.......

 

[ELECT6845]

Husqvarna pics

Here is some pics of the ones i keep for myself. View attachment 290682View attachment 290684View attachment 290685View attachment 290686View attachment 290687

 

[buck futter]

nice saws!

do you guys have a 288 jug available? I have two 181's that are complete and I think one of them would look good with a bigger jug on there.

let me know.

David

 

[srcarr52]

Thanks for the correction Shawn. I guess I've seen "Frankensaws" that were are sorts of ways.......

I've built a few myself. It sucks getting the 181 throttle arm into a 288 case (you have to enlarge the hole a lot). So I would switch the arm and the throttle shaft in the carb if I had the parts. You can quickly tell a 181 case from the lack of the pin above the left-upper AV mount hole.

 

[rattler362]

Here are a couple.

 

[Itsme7]

 

[BloodOnTheIce]

That looks familiar. I'm putting a 288XP together from two partial saws as well.

What saw did that crankcase/tank setup come from? The throttle arm looks different than what's on my 288's.

That throttle arm needs to be replaced, it binds on the crankcase.
And the carb uses the knub, and not the linkage.

 

[J.Walker]

.



.

 

[SawTroll]

.

......

.

Looks very nice for a 2007 saw! :msp_biggrin:

 

[J.Walker]

Looks very nice for a 2007 saw! :msp_biggrin:

Ones a 07 and the other is a 08.

 

[SawTroll]

Ones a 07 and the other is a 08.

What I see is 2009 on the top one , and 2007 on the bottom one? I edited the 2009 one out of my quote! :msp_biggrin:

 

[J.Walker]

What I see is 2009 on the top one , and 2007 on the bottom one? I edited the 2009 one out of my quote! :msp_biggrin:

You still have good eyes I see!