blk05crew
I like 'em green
The 3700 piston compatible with the Craftsman 3.7 I assume? I may need one for the saw I bought this weekend. I don't know the condition of the P/C yet.
Nik's Poulan Thread
- Thread starter FATGUY
- Start date
Help Support Arborist Forum:
The 3700 piston compatible with the Craftsman 3.7 I assume? I may need one for the saw I bought this weekend. I don't know the condition of the P/C yet.
echoshawn
....Beer is good.....
Depends on the 3.7. Thick ring must go with unplated cylinder. Thin ring with plated cylinder
blk05crew
I like 'em green
Thanks, I'm not sure which it is yet or even if it's good or bad haha!
echoshawn
....Beer is good.....
Clean and proper 4000 for $35. Not bad I'd say
echoshawn
....Beer is good.....
Lol not as big a suck as that 245 was, but close 
blk05crew
I like 'em green
Beat to the punch again, lol! I'm gonna have to stay up all hours checking CL if want to find any deals on Poulans anymore! Nice find Shawn!
Very nice how's compression?
Clean and proper 4000 for $35. Not bad I'd say
echoshawn
....Beer is good.....
Haven't put a gauge on it yet, but it feels right. I'll dig into it later, pull the muffler, etc
might have one to help you with. i'll check what I have.
ILikesEmGreen
Another crazy Poulan Fan
So I finally got around to tearing my 25 (33cc) down last night. Knew it was scored a little bit, compression was low, etc. Had ran it a little bit since I've gotten it but it was a scrap yard find for $5 so I wasn't too mad. When I took the top handle off and removed the reed, I found a small wood chip stuck in the corner of the reed block holding it open slightly on one side. Pulled the cyl and the crank case had a bit of oil in the bottom... Probably why it smoked like you were fogging bees. Figure the check valve sh** the bed causing that. The P&C were in this shape... Not sure if that's salvageable or not. I kinda doubt it.
Always wanted a Micro ever since I had the Ertl toy version as a kid. My son is pretty fond of this little saw too, as he was the one who actually spotted it. Looks about like I can find me a good runner... Maybe even a 5cc upgrade, hehe, for about the same money as I'm looking to spend in parts to fix this one.
On another note, what's up with that flywheel? Looks like the metal came off where the magnets are...
Sent from my E6782 using Tapatalk
Always wanted a Micro ever since I had the Ertl toy version as a kid. My son is pretty fond of this little saw too, as he was the one who actually spotted it. Looks about like I can find me a good runner... Maybe even a 5cc upgrade, hehe, for about the same money as I'm looking to spend in parts to fix this one.
On another note, what's up with that flywheel? Looks like the metal came off where the magnets are...
Sent from my E6782 using Tapatalk
Are you a professional? That's all who are allowed to run 3700&4000 saws. Not my rules. Says so on the fuel tank
That's why I'm not allowed to run any of my saws anymore and I have the scars to prove why..
Toast. Micros are a dime a dozen. I'd add it to your next scrap run unless it had sentimental value. Which it does nitSo I finally got around to tearing my 25 (33cc) down last night. Knew it was scored a little bit, compression was low, etc. Had ran it a little bit since I've gotten it but it was a scrap yard find for $5 so I wasn't too mad. When I took the top handle off and removed the reed, I found a small wood chip stuck in the corner of the reed block holding it open slightly on one side. Pulled the cyl and the crank case had a bit of oil in the bottom... Probably why it smoked like you were fogging bees. Figure the check valve sh** the bed causing that. The P&C were in this shape... Not sure if that's salvageable or not. I kinda doubt it.
Always wanted a Micro ever since I had the Ertl toy version as a kid. My son is pretty fond of this little saw too, as he was the one who actually spotted it. Looks about like I can find me a good runner... Maybe even a 5cc upgrade, hehe, for about the same money as I'm looking to spend in parts to fix this one.
On another note, what's up with that flywheel? Looks like the metal came off where the magnets are...
Sent from my E6782 using Tapatalk
Me too, damn shame all those saws on my shelf and I gotta hire someone to run them.
Pm me I might have some stuff to help youSo I finally got around to tearing my 25 (33cc) down last night. Knew it was scored a little bit, compression was low, etc. Had ran it a little bit since I've gotten it but it was a scrap yard find for $5 so I wasn't too mad. When I took the top handle off and removed the reed, I found a small wood chip stuck in the corner of the reed block holding it open slightly on one side. Pulled the cyl and the crank case had a bit of oil in the bottom... Probably why it smoked like you were fogging bees. Figure the check valve sh** the bed causing that. The P&C were in this shape... Not sure if that's salvageable or not. I kinda doubt it.
Always wanted a Micro ever since I had the Ertl toy version as a kid. My son is pretty fond of this little saw too, as he was the one who actually spotted it. Looks about like I can find me a good runner... Maybe even a 5cc upgrade, hehe, for about the same money as I'm looking to spend in parts to fix this one.
On another note, what's up with that flywheel? Looks like the metal came off where the magnets are...
Sent from my E6782 using Tapatalk
echoshawn
....Beer is good.....
you can't get much better than those two saws for 65 -70 cc saws.I'm not a pro, I just play one on the interwebs
The 2 together
Similar threads
