Partner Chainsaw Thread

[captain dangers]

and here is my old partner p100 super, I havnt used it in anger yet, but I do have a brand new 36 inch Oregon bar and chain combo for it ;o)

 

[kz1000]

Your going to have me putting this sucker together aren't you!

 

[kz1000]

Wish you had a video of that cut Mark!

 

[kz1000]

Great! Now look what you have done Mark--- I tried to get rid of it! Hey, I ran three screws in the oiler gear and it didn't budge, do I have to heat it?

 

[Modifiedmark]

Great! Now look what you have done Mark--- I tried to get rid of it! Hey, I ran three screws in the oiler gear and it didn't budge, do I have to heat it? View attachment 655838

I don't remember what I done with that gear. Seems it was threaded and I used a puller on it? Make sure the oiler is pulled out the front first.
I think the crank seals were the same as the P100 which are standard easy to get metric seals. 15x26x7 and 20x48x7

Here is the IPL

 

[kz1000]

Hey! I got the gear off with a little heat. What did you do for a case gasket and do you think a 3120 coil would work. Thanks!

 

[kz1000]

You started this, I was going to sell it!

 

[Modifiedmark]

I think i made a case gasket for it. I don't have a clue on a 3120 coil. I know the coil i posted earlier will work

 

[kz1000]

I looked up that coil and it fits 3120 also. thanks!

 

[kz1000]

Got the bearings and added redneck paint job so far.

 

[kz1000]

It"s ALIVE!!!!! Need to glue some shoes on the clutch but it sounds good.

 

[kz1000]

Hey, anybody know what other saws used the same clutch as this r440t? All my shoes are shot. Thanks!

 

[fechtichmac]

Hey, anybody know what other saws used the same clutch as this r440t? All my shoes are shot. Thanks!

Clutch drum of later models (smaller diameter) - so as p100 will fit your clutch without the glued shoes.
Also the later p100 clutch will fit.
E.

Gesendet von meinem SM-G928F mit Tapatalk

 

[fechtichmac]

Hey, anybody know what other saws used the same clutch as this r440t? All my shoes are shot. Thanks!

...Your clutch has glued linings ?

Gesendet von meinem SM-G928F mit Tapatalk

 

[kz1000]

...Your clutch has glued linings ?

Gesendet von meinem SM-G928F mit Tapatalk

Yes it had glued linings, now has sawdust like parts.

 

[fechtichmac]

Like this your clutch will fit the smaller drum,wich are still available[emoji106]

Yes it had glued linings, now has sawdust like parts.

Gesendet von meinem SM-G928F mit Tapatalk

 

[fechtichmac]

Hey Guys!
Just picked this up and trying to decide what model it is. It has the 56mm piston so that narrows it some. It was missing the coil and I put a 55 husky coil on to try it, I can get it to pop but I think I sprayed to much oil in the lower end to lube the bearings. Anyway I would appreciate any info and whether to sell it whole or would I get more parting it out? I tried to do a compression test on it and couldn't turn it over without the de-comp pushed, so seems to have a ton!

Remove the remaining lining...

Gesendet von meinem SM-G928F mit Tapatalk

 

[kz1000]

Thanks man, just ordered one for a p100 made after 1977 hope that's right.

 

[Timberjack zack]

Anyone have a p100 starter spring or a starter assembly they want to sell

Sent from my SM-G930V using Tapatalk

 

[captain dangers]

Anyone have a p100 starter spring or a starter assembly they want to sell

Sent from my SM-G930V using Tapatalk

I have a brand new starter assembly, but alas I'm the other side of the pond and carriage will be a fortune ;o( try looking for an old partner k1200 disc cutter, as they are based on a p100 ;o)