Pioneer chainsaws

[rynosawr]

Thanks KZ1000!!!!

Pics of my new-to-me P41

 

[kz1000]

Man that's a clean saw! Good luck with it, bet it fires right up.

 

[rocketnorton]

nice shape.

while im here, in need of p series oil cap. for farmsaw.

 

[hillwilliam]

nice shape.

while im here, in need of p series oil cap. for farmsaw.

I've seen plenty of them on Evil-bay but I don't think I've seen fuel caps.

 

[DSS]

Early P-41 had no brake. The designation for one with a brake is P-41S. Yours is a H, which means half wrap (handle). A full wrap is a P-41W.

 

[rocketnorton]

I've seen plenty of them on Evil-bay but I don't think I've seen fuel caps.

ino oil [smaller of the 2] cap.

 

[hillwilliam]

ino oil [smaller of the 2] cap.

http://www.ebay.com/itm/PIONEER-P42...211?pt=LH_DefaultDomain_0&hash=item5403e3e2ab

 

[kz1000]

I'll check on shipping from AZ. tomorrow, can't be that much.

 

[Lou]

OrderTree (probably other sources too)
HOP-507475168 $7.54.
Gas caps swelled and were often replaced. Not so oil caps, they are still available.
Lou
PartsTree has it too (507475168), surprise it's more expensive. $9.00± shipping seems steep to me. USPS can probably beat that, and it goes in your mail box.

 

[67L36Driver]

Pioneer 600 on Craigslist in Harrisonville, Mo. (KC Mo. List)
Eighty miles from me. Twenty miles past Blondie's BFF in Grandview, Mo..
I've been known to make the jump for a saw purchase.

 

[rocketnorton]

Pioneer 600 on Craigslist in Harrisonville, Mo. (KC Mo. List)
Eighty miles from me. Twenty miles past Blondie's BFF in Grandview, Mo..
I've been known to make the jump for a saw purchase.

imo, the best lookin [and sound, along w/ra] pioneer. $60. for this one. runs/cuts good as it looks...

 

[54stude]

I have a p60 that needs a ring, and I was wondering how many ring variations this saw has. I have not torn it down yet, but know it needs a ring from previous owner (original owner). The diameter is 57.1mm. But what should the thickness be? I have noticed there is a poulan 655 still available, but there seem to be some 57.2 mm lambretta scooter rings on eBay that might be close enough to file the ends and run? So what thickness rungs should a p60 have.

 

[Acornhill]

Need help with ID of rings they are 2 " closed .060 thick 2.10 open bag says 473 could be 155

 

[Acornhill]

50 mm x 1.49

 

[kz1000]

ino oil [smaller of the 2] cap.

Weather has been crap here and lots of Honey do's, did you find a cap yet? I have one in my truck and will ship Monday if you still need it.

Also looking for a diagram showing the switch wiring on a 3270 and still need 650 bar studs. Thanks

 

[Acornhill]

Cap will be posted on the bay tomorrow for 5.99 shipped

 

[kz1000]

Heck, it would cost me that to ship it!

 

[fossil]

Need help with ID of rings they are 2 " closed .060 thick 2.10 open bag says 473 could be 155

Pioneer 1072, 1074, 2071 and others use 473155 which is a much smaller bore (1.625") than those.

The 2400, 2460, 3200, 3072 have a 2" bore. Maybe for them?

 

[Acornhill]

Caps are listed on bay 507475168 oil cap

 

[Acornhill]

Pioneer 1072, 1074, 2071 and others use 473155 which is a much smaller bore (1.625") than those.

The 2400, 2460, 3200, 3072 have a 2" bore. Maybe for them?

thank you , yes they are so close to a 245A Poulan as well.