Pioneer chainsaws

[Acornhill]

Anyone have a P10 11 or 12?

Sent from my LG-D800 using Tapatalk

 

[Acornhill]

Pioneer big P series starter pulleys? 475361 metal 475401 plastic and 475362 will they all swap back and forth on saws?

Sent from my LG-D800 using Tapatalk

 

[oronocova]

Another bump for a picture of the throttle linkage on a RA?

Also, anyone have any advice on material for a crankcase/cylinder gasket?

 

[Perry pioneer]

One RA I made my own gasket from auto parts store sheet material, the other one I went gasket delete and used motoseal. I'll get you a picture of linkage.

 

[Hoggwood]

Pioneer big P series starter pulleys? 475361 metal 475401 plastic and 475362 will they all swap back and forth on saws?

Sent from my LG-D800 using Tapatalk

I have interchanged the last two numbered pulleys on a P41 with success.

 

[Perry pioneer]

RA linkage round end goes down on the carburetor.

 

[Perry pioneer]

I really love these old Pioneers 103 cc, dual port muffler sounds bad ass yeah !!!

 

[paul hill]

The info I have is that the 41-60 series all used the same one. Are you looking for one?

 

[Acornhill]

I have one of each and was wondering which one to use.

Sent from my LG-D800 using Tapatalk

 

[paul hill]

Just picked up a P61 in decent shape. Traded it to a friend for a little Husky 350 I rebuilt and got a Granberg Alaskan mill thrown in on the deal.

Does anyone have a part number for the 61 rings or better yet an IPL for the 61thst they'd share?
I have a P60 and it seems like most but not all of the parts are the same as the 60.

 

[paul hill]

I just looked and it shows 475362 for the 41,51, and 60 according to the IPL. Hope that helps.

 

[Acornhill]

I am jealous , rings on bay cheap for that

Sent from my LG-D800 using Tapatalk

 

[Perry pioneer]

I don't have any information on rings for your saw but if you find out the size of them I'm sure you can get some cabers on ebay from the Greek. That sawsaw really clean I bet it's got some real balls!

 

[paul hill]

Thank you.

I traded for it thinking I would put it up for sale. I might have changed my mind already. I haven't fired it up yet because it looks to need a new fuel line, filter, and probably a carb kit. Decomp is plugged so I thought I'd save my shoulder until I know its going to get some fuel. It's got spark and definitely compression!

Only real problem is a piece broken off the muffler/clutch cover. I'll probably replace it with just a clutch cover from another P series and do away with the muffler/clutch cover.

 

[Acornhill]

Paul, it seems you have many in that series 50 60 61 655 etc. You are becoming the west coast pioneer guy

Sent from my LG-D800 using Tapatalk

 

[Acornhill]

Here is a picture

Sent from my LG-D800 using Tapatalk

 

[paul hill]

Thank you for sharing.

I'm just lucky enough to have a few of these saws that I really enjoy.

Now that KZ1000 moved out of northern Az, I might have a shot at scrounging up some parts/saws!!

 

[hillwilliam]

Thank you for sharing.

I'm just lucky enough to have a few of these saws that I really enjoy.

Now that KZ1000 moved out of northern Az, I might have a shot at scrounging up some parts/saws!!

I keep hinting to you that you have too many saws - maybe I'm just jealous. It would be about impossible to pass up a big Pioneer anyway. Congrats on the good fortune!

 

[backhoelover]

View attachment 479468 View attachment 479472 View attachment 479468 View attachment 479472 RA linkage round end goes down on the carburetor.

 

[backhoelover]

that is one clean ipl book