Pioneer chainsaws

[Cookie]

Local classifieds for 20$. Needed a carb kit. Nice little saw, prolly pass it on to the FIL.

 

[Beavers]

View attachment 665288
Can anyone tell me how many DL for 36 inch pioneer bar ? Any help would be dandy. Thanks

Here is my 3/8 -36" Bar , Pioneer Chain drive link in Pic is 119DL

 

[Cookie]

Looks like the same one to me. 119 it is. Thanks

Here is my 3/8 -36" Bar , Pioneer Chain drive link in Pic is 119DL

 

[Cookie]

Looks like the same one to me. 119 it is. Thanks

Here is my 3/8 -36" Bar , Pioneer Chain drive link in Pic is 119DL

 

[Beavers]

Looks like the same one to me. 119 it is. Thanks

Be careful your Rim is not .404 and that they match up.

 

[Cookie]

Have a 3/8 Rim to replace the .404 off this p60. Thanks. Bar is a 3/8 aswell

 

[ML12]

Decided to build a tool for installing/removing wrist pin bearings on the large pioneers. Should work for all 4XX, 6XX, 7XX, 17XX models that use the B-108 needle bearing.




it is a shame that i'll likely never have to use it again now though.

 

[ML12]

Also, picked up this P50 last night for $50, guy put a carb kit in it but couldn't get it to idle. The needles were way out. Needs fuel lines, a new clutch assembly and some handle bar tape/tube/grip to hide the dings.





Took the muffler off and the top end is clean, only blows 132psi though. has thin rings.

Should make a nice spare, to my other spare.

 

[rocketnorton]

Decided to build a tool for installing/removing wrist pin bearings on the large pioneers. Should work for all 4XX, 6XX, 7XX, 17XX models that use the B-108 needle bearing.

View attachment 668751
View attachment 668752

it is a shame that i'll likely never have to use it again now though.

I might know couple guys need one.

 

[ML12]

I might know couple guys need one.

I can bring it by when I drop of the mac parts.

 

[Beavers]

I might know couple guys need one.

l,am in for one.

 

[rocketnorton]

I can bring it by when I drop of the mac parts.

jk. have needed one & prolly will again someday. beavers prolly use it more than me. he's put some nice ones together.
+ thx on mac stuff.

 

[2stroke_shaman]

Also, picked up this P50 last night for $50, guy put a carb kit in it but couldn't get it to idle. The needles were way out. Needs fuel lines, a new clutch assembly and some handle bar tape/tube/grip to hide the dings.

View attachment 668755

View attachment 668756

Took the muffler off and the top end is clean, only blows 132psi though. has thin rings.

Should make a nice spare, to my other spare.

I forgot I had these . Intended for a snowmobile . There is 8" of grip if you cut the end off 3/4 tight ID.

 

[Aaron1082]

Hey all, I'm not sure if it's been covered before, I'm new to the forum and need an air filter and cover for a p26. Got one in a pile of lawn care stuff and I haven't really had much luck on ebay or CL. If there's another model number that will fit...I'm game. I just don't have much experience with these saws to be able to tell what fits what. Like a crash parts digest for chainsaws. Lol

 

[Cookie]

Welcome. The covers are tough to find in good shape. I’m on the hunt fir one aswell.

 

[Acornhill]

I will post what I have available later tonight


Sent from my iPhone using Tapatalk

 

[2stroke_shaman]

Hi Aaron ,
Welcome to the best Pioneer page . If a p28 will work I have a nos filter but no cover. Cookie has a P25 and a P28 . He might know if its the same.
Tom

 

[Cookie]

My p25 has the small 1/2 felt filter. P28 has the full size filter.

 

[2stroke_shaman]

My p25 has the small 1/2 felt filter. P28 has the full size filter.

Thanks Kevin ,
My book stops at the P25.

 

[Acornhill]

What do these fit?

Sent from my iPhone using Tapatalk