I'm trying to put the key and cam back on.
Pioneer chainsaws
- Thread starter WesternSaw
- Start date
-
- Tags
- operator manual
Help Support Arborist Forum:
I had to give the clutch a hit with rubber hammer to get it on over that key but that's not an option on this side.
The cam is pretty thin, so I'm a little worried about using force.
Should the cam just slide over the key?
The cam is pretty thin, so I'm a little worried about using force.
Should the cam just slide over the key?
p61 western
ArboristSite Guru
Pull the flywheel key out to install your parts, and then put the key back in. Don't file or hit anything.
Use a wire cutter \dike to grab the key and rock it upwards. It should come out.
flat on key needs to be parallel w/cam.
if it's angled up at all, will get wedged as in yer pics.
if it's angled up at all, will get wedged as in yer pics.
Ah I see now the key goes under. There may be a bur under the sleeve.
Like the other guys say, pull the key with a pair of dikes (wire cutters) and file it to fit. No need to fight it. Make sure the cam is the right direction. Look for the arrow denoting rotation.
Also, what is that window cut into the case behind the cam? I don't remember that on those Pioneers. Also, it looks like I can see the oil seal garter spring through that window. If so, that seal is in backwards.
Chris B.
p61 western
ArboristSite Guru
Took this one out and got it dirty yesterday. Sure is a good running saw. Was running a 24" bar and a 8 pin sprocket no problem.
I'm running into a problem in getting a 20 in.3/8 .050 gauge bar for my 1100.I don't know what bar mount pattern it's supposed to take.Acres' site says it's supposed to take a K095 mount,but has a pic of a D196 mount.I measured the studs by the threads & it was at just under 8 mm.The D196 is 9.5 mm.
Ed
Ed
p61 western
ArboristSite Guru
May be difficult to find something not .058.
Ed,
Get a 3/8 extension spring (which has an ID of 5/16) and snip 3 or 4 coils off for each bar stud. That will bring the stud size up to 3/8 size up to. They used to supply an "S" clip with the Windsor UXL bars to do that but they are hard to come by and the springs work just as well.
Good eye, it is. I put the other side in the right way . That s the original S620 case with those cutouts.
I have often grabbed one of those big copper colored staples from a heavy duty cardboard box and rebent the ends to fit around the bar studs, has worked many times to get a saw back out and cutting again. Many other ways to do it but sometimes I just use something just sitting there and make it go.
Thanks Tim & PioneerGuy600,I've got an S clip on the way from Bob Johnson.I found the S clips on Ebay & chainsawr,but I refuse to pay $8 or $9 for an S clip from either place.
Ed
Ed
Walter Glover
ArboristSite Guru
Hello fellas, I am looking for a set of clutch shoes for my P51. Any advice on where to get such?
Thanks in advance
Walter
Thanks in advance
Walter
You could try Bob Johnson,he used to be a Pioneer dealer & still has parts.
Ed
Ed
Walter Glover
ArboristSite Guru
Thank you Ed. How would I contact Bob?
His phone # is:607-638-9397.Mon.is his busy day,you can try him,but may be better to try on Tues.He's open from 9:30 a.m.-12:00 noon,then he closes for lunch & reopens at 1:30 p.m.-5:00 p.m. Mon.-Fri.Good luck Walter!
Ed
Ed
Finished,it took awhile.
Similar threads
- Locked
