MCW
Somebody's talking crap here & it ain't the tree!
Sorry to disappoint you Andrew but that IS NOT precision falling. You're at least 5mm out on the left side. Sharpen up your act old son and only post pictures when you get it right...
Stihlmans Wood,Tree cutting ramblings...........
- Thread starter Stihlman441
- Start date
Help Support Arborist Forum:
Sorry to disappoint you Andrew but that IS NOT precision falling. You're at least 5mm out on the left side. Sharpen up your act old son and only post pictures when you get it right...
Stihlman441
Addicted to ArboristSite
Mastermind
Work Saw Specialist
Stihlman441
Addicted to ArboristSite
At it again,16 split mtrs out of this Redgum.
It helps when you wear one of these T shirts on the big jobs
At it again,16 split mtrs out of this Redgum.
It helps when you wear one of these T shirts on the big jobs
At it again,16 split mtrs out of this Redgum.
koomie
ArboristSite Operative
That's pretty good looking wood bro
MCW
Somebody's talking crap here & it ain't the tree!
Did you end up getting that tattooed on your right butt cheek as well? I know you were thinking about it.
Stihlman441
Addicted to ArboristSite
It was the left cheek get it right.
If i recall you bloked up some of that tree.
If i recall you bloked up some of that tree.
MCW
Somebody's talking crap here & it ain't the tree!
Now I remember! That was the one that had fallen on the fence and Danny was wailing into it with his cordless Stihl
I also cut it up with your 460, 441, and Masterminded 241.
Stihlman441
Addicted to ArboristSite
Yep.
MCW
Somebody's talking crap here & it ain't the tree!
Dandy and spiffy old chap.
Stihlman441
Addicted to ArboristSite
Next on the menu afew very large Sugars in the middle of a canola crop,cocky wonts um gorne they get in the way of spraying and cropin.
Nice widow maker in this one.
660 with a 36'' bar
I dont think they come any bigger than this one.
Cut some grooves in the stump build a fire ontop and the plan is the burn them out over the rest of the week.
Nice widow maker in this one.
660 with a 36'' bar
I dont think they come any bigger than this one.
Cut some grooves in the stump build a fire ontop and the plan is the burn them out over the rest of the week.
nice one 441, that big sugar made your 66 look like 23
VinceGU05
PSA vitim.
Sure is a big ugly bastard that one !! Not a 5 min job either!
Stihlman441
Addicted to ArboristSite
Just another day out at the plantasoin battling wind,rain and cold,would be half way along bye days end.
Stihlman441
Addicted to ArboristSite
Had afew dodgy ones with rot in them can be a bit tricky.
I dont know how you blokes do um but i bore cut and then release them at the back last to try and stop them splitting up the middle.
I dont know how you blokes do um but i bore cut and then release them at the back last to try and stop them splitting up the middle.
Stihlman441
Addicted to ArboristSite
All done,will leave this here until the Canola crop is harvested next year by then the bark will have fallen off and it will be a bit dryer.
VinceGU05
PSA vitim.
Ok.. It's been over a month. Time for an undate!
Stihl working hard
Is it Friday yet
Come on Andrew don't leave us hangin
Stihlman441
Addicted to ArboristSite
Nothing new just blocking and splitting every day hohum.
But i will have a yack about sprocket noses.
I have been using 20'' GB Ti bar for years and have put hundreds hrs on um with allmost no probs.
As you blokes no there no good anymore made in China bla bla.
Get some Tsumura/Carlton bars they said.
The paint on the Ti bars dont last long they said,give ya a tip that loverly finish on the Tsumura/Carlton dont last long as well.
In the pick the top one is a brand new sprocket with the 6 pins in the bearing area.
On the right is a sprocket from a Ti bar that has done hundreds of hrs as seen in the wear.
The left one is of a Tsumura bar that has about 6 to 8 hrs on it with the 4 pins in the bearing area.
Bottom pic shows the 4 pin Tsumura arrr no good.
What do yas think ?.
But i will have a yack about sprocket noses.
I have been using 20'' GB Ti bar for years and have put hundreds hrs on um with allmost no probs.
As you blokes no there no good anymore made in China bla bla.
Get some Tsumura/Carlton bars they said.
The paint on the Ti bars dont last long they said,give ya a tip that loverly finish on the Tsumura/Carlton dont last long as well.
In the pick the top one is a brand new sprocket with the 6 pins in the bearing area.
On the right is a sprocket from a Ti bar that has done hundreds of hrs as seen in the wear.
The left one is of a Tsumura bar that has about 6 to 8 hrs on it with the 4 pins in the bearing area.
Bottom pic shows the 4 pin Tsumura arrr no good.
What do yas think ?.
MCW
Somebody's talking crap here & it ain't the tree!
So the tip you had let go mate was the older 4 rivet nose? If so they did have a habit of that hence the newer noses run 6 rivets. Is the new nose one I sent you?
How long have you had that bar for it to be a 4 rivet nose?
How long have you had that bar for it to be a 4 rivet nose?
