Sure is quiet in here....do I need to start a fight?

[IEL]

Exams went well, think I did good.
Picked up a tube of bondo dent and glaze putty, that should make the mac look good. I am talking to my neighbor tomorrow about borrowing his blast cabinet for the day. He has said I can use it any time, but I will ask anyways.
Also, a bit of a DooHH moment. I was at the grocery store dropping off a resume, and I didn't even think to pickup oven cleaner. I have to go back anyways tomorrow, so I guess I will get it then.
Any tips for honing a iron lined saw cylinder? Can it be done very lightly without replacing rings? I think it only needs maybe a thou or two off.

Now that I think about it, it wouldn't even need a thou off. Just a quick 5 second honing is all it would need. Not sure if I can get rings for this old a mac?

 

[roncoinc]

Oh my,,,,tough day here too ...

spent most of it in a hole in the water on the ocean.

i had to quit fishin,,wrist got to sore reeling them in !!

now ou to the cooler with baggies,,etc...take care of em..

 

[dancan]

Sculpin tourny ?

 

[tbone75]

Oh my,,,,tough day here too ...

spent most of it in a hole in the water on the ocean.

i had to quit fishin,,wrist got to sore reeling them in !!

now ou to the cooler with baggies,,etc...take care of em..

Good day Ron !

Wheres the pix ?

Just another fish story ? LOL

 

[tbone75]

Tore the MS170 apart , can't find anything bad in there. But it was full of fuel in side ! Now guessing the carb is the problem. So flooded no way it could start.

 

[dancan]

John , I found that Patrone stuff up here, might be a while before I can cross that one off the list .....

 

[Jimmy in NC]

Cleaned the shop tonight in preparation for a Dolmar 7900 coming over Friday for a top end. So sad he went BB instead of stock.....



Jimmy

 

[tbone75]

John , I found that Patrone stuff up here, might be a while before I can cross that one off the list .....

Pricey chit !! LOL

 

[roncoinc]

Cleaned the shop tonight in preparation for a Dolmar 7900 coming over Friday for a top end. So sad he went BB instead of stock.....



Jimmy

good for him !!

grinder and massage that BB kit a bit and wont want a little 79cc saw anymore !!
best thing i ever did..

 

[tbone75]

good for him !!

grinder and massage that BB kit a bit and wont want a little 79cc saw anymore !!
best thing i ever did..

Mine sure runs good !!

 

[pioneerguy600]

John , I found that Patrone stuff up here, might be a while before I can cross that one off the list .....

That stuff is harsh at 40% and comes out of Mexico. I`ve had a few tastes of it and it hits hard n fast.

 

[Jimmy in NC]

Time.




Jimmy

 

[pioneerguy600]

Time.




Jimmy

Nite Jimmy:

 

[tbone75]

Time.




Jimmy

Nite Jimmy

 

[tbone75]

That stuff is harsh at 40% and comes out of Mexico. I`ve had a few tastes of it and it hits hard n fast.

Little much for DanCan't ! :hmm3grin2orange:

 

[pioneerguy600]

Little much for DanCan't ! :hmm3grin2orange:

Think he might just fly around in circles after ingestion.

 

[tbone75]

Think he might just fly around in circles after ingestion.

Can't say I didn't a few times ! LOL Stihl like that stuff ? LOL

 

[pioneerguy600]

Can't say I didn't a few times ! LOL Stihl like that stuff ? LOL

I have only ingested a small amount of it and could see that if I ingested more of it I might get really light on my feet.....LOL:hmm3grin2orange:

 

[tbone75]

Just hit me !!


I worked on a saw tonight !

 

[pioneerguy600]

Just hit me !!


I worked on a saw tonight !

....:msp_w00t:......