Swap meet...

[rms61moparman]

Looking for a piston and ring for a poulan/craftsman 42cc wild thingy type, piston kit for reference 530071408. PM me please I have paper for a part.

Strato or non???


Mike

 

[sachsmo]

I have a old beat to death 1988 BMW 325ic trade even up for a 166 Dolmar with West Coast filter and full wrap.

 

[sefh3]

Looking for a piston and ring for a poulan/craftsman 42cc wild thingy type, piston kit for reference 530071408. PM me please I have paper for a part.

If its a non strato, then I have one that has a busted crank but the piston and cylinder have low hours.

 

[hemiyota]

Husky 45 parts

I need a choke lever, ignition switch, top a/v spring, and a bar nut...........

 

[super3]

Need A Walbro HD-6 carb.

 

[sefh3]

Need A Walbro HD-6 carb.

What's it fit?

 

[rms61moparman]

What's it fit?

371-372 Husky.


Mike

 

[huskydude]

I sent one to Roncoinc a couple of years ago and it didn't fit his saw. He might still have it.:confused2:

He won't be able to find it though (i've seen his shop)

 

[Johnsobri]

Strato or non???


Mike

If its a non strato, then I have one that has a busted crank but the piston and cylinder have low hours.

Looking for a piston and ring for a poulan/craftsman 42cc wild thingy type, piston kit for reference 530071408. PM me please I have paper for a part.

This would be for a non strato. Thanks for your help!
Brian

 

[Saw Dr.]

Looking for a decent MS-260 (flippy cap) fuel tank.
Also need a nice looking Echo 370 front handle. The saw was straight gassed out of the box, so the handle needs to be nice. Probably should just buy a new one, but just checking.

 

[sefh3]

Looking for a piston and ring for a poulan/craftsman 42cc wild thingy type, piston kit for reference 530071408. PM me please I have paper for a part.

This would be for a non strato. Thanks for your help!
Brian

Will this work? PM me if it will.

 

[sefh3]

I'm looking for a TS350 or Stihl 08 recoil for the older Bosch setup. I need the fan wheel also. If you have any or a parts saw laying around I could use the power head. Trying to finish up some of these projects. I have parts and a few $$ to trade.

Anyone have any of this stuff. I will take parts or projects.

 

[Modifiedmark]

Will this work? PM me if it will.

Scott, ifin that other fella cant use that, I reckon I could. I got a same as new straight gassed one here and I might have something to trade ya for it.

 

[sachsmo]

I have a old beat to death 1988 BMW 325ic trade even up for a 166 Dolmar with West Coast filter and full wrap.

It's really not that bad.

Drove her for 10 years 60 mile commute everyday.

Only retired it cause it only gets 25 MPG and the corolla my brother sold me for $600 gets 35.

 

[komatsuvarna]

Looking for an OEM rev-limited coil for a 365/372/385/390xp. 13,000 or 13,300 limit is fine. $$$$ to trade.

 

[Mastermind]

Looking for an OEM rev-limited coil for a 365/372/385/390xp. 13,000 or 13,300 limit is fine. $$$$ to trade.

I got several. PM me....

 

[tbone75]

Needing a 2 piece coil and off switch for a Husky 61. Should have something you like in trade? TIA

 

[Warped5]

Need a Shindaiwa 488 chain catcher and bar nuts.

I have some Mac parts, stuff and worthless dead presidential portraits.

TIA!

 

[3000 FPS]

I need a trigger for a Dolmar 119. In the picture the coil is at the bottom the trigger is at the top. I have done some testing on the coil with a 18v battery and a spark indicator and know for sure it is good.

From what I can tell the trigger actually sends a small voltage over to the coil which then steps it up high enough to create a spark.

View attachment 261840

 

[Wagnerwerks]

Needing a 2 piece coil and off switch for a Husky 61. Should have something you like in trade? TIA

2 piece from a 266se work?