Swap meet...

[Herd8497]

Need

25" roller nose bar (.404 .063) for an 051.

 

[epicklein22]

No worries...that Tsumara looks interesting. I could cut that and put a roller nose on it...

Believe I have that same bar, large mount husky. Brand new, yours if you want it.

 

[Scooterbum]

yep, carb body, plastic plate, and then metal plate with primer bulb.

I'll check in the AM.

 

[barneyrb]

Thanks, let me know how much....

 

[mdavlee]

I'm looking for a carb for a husky 136. I lost the spring when I was cleaning it and ready to put a kit in it I have some stihl chain and worthless pictures of presidents.

 

[struggle]

I'm looking for a carb for a husky 136. I lost the spring when I was cleaning it and ready to put a kit in it I have some stihl chain and worthless pictures of presidents.

Is the carb anything special. I have a sears 2.2 here with a scored piston that has a carb on it it is a 36cc saw

 

[mdavlee]

Is the carb anything special. I have a sears 2.2 here with a scored piston that has a carb on it it is a 36cc saw

The one I have is a walbro 239. I think it's the same as a few small poulans and craftsman saws. Not sure on the models though.

 

[Arrowhead]

The one I have is a walbro 239. I think it's the same as a few small poulans and craftsman saws. Not sure on the models though.

Is it a WT?

 

[Arrowhead]

Needing a decent looking ms290 air filter cover. round top

 

[struggle]

Will they of these work? One is off a 2.2 other off some sort of string trimmer

Sent from my C771 using Tapatalk 2

 

[mdavlee]

Is it a WT?

Yes it's a wt i believe. I can look again in the morning.

It looks a lot like the one on the right in the picture there.

 

[struggle]

Yes it's a wt i believe. I can look again in the morning.

It looks a lot like the one on the right in the picture there.

WT324 stamped on it. If you want send me an address. It won't have any gaskets in it if the fuel pump is good as I can use it on another saw. It was on a 2.2 craftsman 36cc

 

[mdavlee]

I'll check again tomorrow and see if that number crosses over. I have a brand new carb kit here.

 

[Arrowhead]

Yes it's a wt i believe. I can look again in the morning.

It looks a lot like the one on the right in the picture there.

I just used a wt kit yesterday and didn't use the new spring.
PM me your addy and I'll send it on it's way in the morning.

 

[Whiskers]

Anybody have any 026/026 Pro parts saws laying around you'd like to trade off? I've got some 044, 051, 076, and a bunch of other stuff laying around that I can't remember right now.

 

[diggers_dad]

I need of the chain adjuster parts for this cover. Craftsman 2.2 cid saw.
Since everyone here hates these saws that should mean you have lots o parts in a box some where for it:msp_biggrin:

Sent from my C771 using Tapatalk 2

If no one else has chimed in send me a PM and I'll get one on the way to you. I'm sure I have 3 or 4 laying around.

dd

 

[half_full]

S25CVA coil

Looking for a Poulan S25CVA coil. I have very few parts but do have $.

to trade?
husky 266 top cover, Maybe a carb from a 272? I can dig for anything of interest but I tend to not keep big parts laying around.

 

[vw_motorsports]

Looking for a Poulan S25CVA coil. I have very few parts but do have $.

to trade?
husky 266 top cover, Maybe a carb from a 272? I can dig for anything of interest but I tend to not keep big parts laying around.

pm sent

 

[struggle]

If no one else has chimed in send me a PM and I'll get one on the way to you. I'm sure I have 3 or 4 laying around.

dd

PM sent

 

[bucknfeller]

019T Complete saw, compression feels good, no spark. Not sure about anything else. Partially disassembled.

031AV Complete saw, compression feels good, piston looks good through ex. port. muffler has been boogered/welded, makes spark, but needs plug wire. That's all I know about it. Partially disassembled.

Parts Needed:
Husky 445/450 wrap
026 coil
18" or 20" Husky small mount 3/8" .050 bars
Always looking for husky parts/project saws.

Thanks in advance,
Josh

So I guess I'm not the only one who doesn't need this stuff?