Swap meet...

[sefh3]

I no it's not a chainsaw but I picked up a Ryobi 410R rototiller. Any one have a motor for one of these? Pretty good shape but the piston and cylinder is toast. I have parts to trade.

 

[67L36Driver]

I have a similar rear handle version that I use for carving and I have replaced that pump 3 times in 4 years of carving! Most of the parts saws I come across from that family if saws the pump gears are usually still good so I don't think it was very common.

Sent from my XT1031 using Tapatalk

He is going to get a goober of white lithium grease around the gears when he goes back together.

 

[rednecksawman]

here is a picture of the coil that I need. Tom

im still looking I got the flywheel I stuck that stuff someplace .

 

[tomdcoker]

im still looking I got the flywheel I stuck that stuff someplace .

Thanks. I know how that goes. I have parts that I know are in the shop somewhere, but finding them is impossible. Tom

 

[rednecksawman]

Thanks. I know how that goes. I have parts that I know are in the shop somewhere, but finding them is impossible. Tom

yea find stuff like that all the time when I DONT need them lol

 

[bplust]

I need a Jonsered 2094, 2095, Husqvarna 394, or 395 top end.

Parts or paper to trade.

Bryan

 

[tomdcoker]

here is a picture of the coil that I need. Tom

BUMP=BUMP=BUMP

 

[rednecksawman]

Tom i have looked high and low for that coil. I have the flywheel if you need it and the muffler and gas tank

BUMP=BUMP=BUMP

i

 

[tomdcoker]

Tom i have looked high and low for that coil. I have the flywheel if you need it and the muffler and gas tank

i

I know how that is. Like I told you before I have promised someone parts that i knew I had, but could not find them. I appreciate that you looked for it, but I only need the coil. Please just remember me if you run across it. Thanks for the effort. Tom

 

[bplust]

I'm looking for a Jonsered 2051/2054/2055 choke link. I already have the grommet.

Parts or paper to trade.

bump!

 

[Flat47]

Looking for Husky 372 XTorq hi-top air filter cover and air filter mount for the screw-down filter.

Bolt holes are different on the Xtorq. I think the bolt holes on the filter mount are nearly horizontal on the XTorq- already bought the the wrong one off an XP.

 

[surfincr]

before i go the ebay route anybone have any of the following:

036 recoil
026 carb, 2 x air filter, cover
260 handle

not urgent but looking for an ms660 with a bad engine

have 021 engine assembly w/coil perfect shape, 021 handle, ht131 engine, an unknown stihl weedwacker engine, or cash also have a craftsman 3.7/18" with case, extra chain, and tools i can trade, needs the handle bar buffer and carb kit

 

[RedneckChainsawRepair]

Mantis coil. I have one that was scored. No clue if coil was good or bad, came in apart. I will see if still on the shelf. Been there a couple years now. So red wire coil is the one needed?

Guess I need to look for that poulan muffler cover for a guy too .

 

[RedneckChainsawRepair]

Mantis coil. I have one that was scored. No clue if coil was good or bad, came in apart. I will see if still on the shelf. Been there a couple years now. So red wire coil is the one needed?

Guess I need to look for that poulan muffler cover for a guy too .

Ran out during commercial break during BB game. Mantis coil I have is grey with black wire. Oh well.

Still forgot to look for poulan muffler cover.

 

[nstueve]

Stihl 015 3/8 clutch drum.

I know someone had one of these for me and I found the oiler gear on eBay. Just need that drum now...

 

[MS460WOODCHUCK]

Hey guys I'm needing the little screw that holds on the fuel tank guard for a 044. I do not have another around to compare or I would just get one at the local hardware. I would hate to run the wrong screw in and ruin the plastic threads of the handle. PM me if you can help me out.

 

[cat-face timber]

Anybody want to trade a left bucking spur for the right one?
I need the one from the clutch cover if anybody has one.
Husky 288.

 

[LowVolt]

Looking for a decent 372xp muffler. Rust is ok, just no dents. Send me a pm.

Thanks!

 

[Mo. Jim]

Long shot mabey, I have Redmax G300ts that I need a coil for, any help would greatly appreciated.

 

[Guido Salvage]

Long shot mabey, I have Redmax G300ts that I need a coil for, any help would greatly appreciated.

Terry Landrum is a Redmax dealer, can he help?