Swap meet...

[computeruser]

I'm still in the market for another 044 project after selling off my last one, which was a really dumb thing for me to do. Willing to trade some cash for the right one.

 

[Lunchbox]

need dolmar/stihl

In need of a coil for a dolmar ps6000i.
handlebar for an 025.
maybe couple other parts.

have this to go..seems to run pretty good..

 

[mlh29]

stihl 20 inch rescue carbide chain

I have a new never used chain off a ms460 r saw. It is the newer full carbide chain in size 3/8 x 72 x .63gu. Never used, probably will never use, needs to go
Have a good used es bar and 3 or 4 full chisel reg chains in above size also.
converted 460 r to 20 3/8x .50

Prince mfg 3000psi royalplate tie rod cylinder 4x30 AS new, used to mock up a splitter that I ended up using a 36 stroke on(read has correct fittings to fit 1/2 hose and may have fluid in it, otherwise new)

haldex barnes 16gpm 2 stage pump (same as cylinder cond above, customer wanted 5x36 and 28gpm which was way overkill for his splitter needs)

Looking for
ms361 wrap handle kit
green backs
stihl yellow 3/8 x50ga in 60,66,72,84 drivers
ms260pro with 3/8 sprocket ( like new)

email [email protected] with requests

 

[rupedoggy]

I have a box full of 394 stuff. Only half a crankcase (starter side), no gas tank and no handlebar, but most everything else including cylinders.

 

[rupedoggy]

288 good top plastic, new cylinder and piston (OEM) amd one good used cylinder, other stuff too.

 

[rupedoggy]

Box with Dolmar 153 stuff. Crankcase, gas tank, Handlebar, scored cylinder/piston. Almost enough to build a saw.

 

[rupedoggy]

Bunch of parts for the 272/268/66 type.

 

[rupedoggy]

Crankcases, cylinder, small parts galore for the 372. No gas tanks Two full wrap handlebars that have been hit by the chain quite a few times but still hanging in there.

 

[rupedoggy]

041 Stihl complete but sitting since I got it couple years ago. 031 same thing.

 

[KTM640]

Rupe, PM sent on the 268/272/61 parts.

 

[Eccentric]

041 Stihl complete but sitting since I got it couple years ago. 031 same thing.

Sending a PM about the 031 and 041...

 

[forestryworks]

lookin' for an 044 powerhead. P&C needn't be in good condition as I have an extra.
I'll even eyeball an 046 powerhead with a bad P&C as well.

I got:
361 half wrap, small clutch cover
361 gas tank assembly, stripped handle mounts

066 half wrap, small clutch cover

440 small clutch cover
440 standard muffler cover

3 or 4 20" b&c in stihl large mount - 3/8ths .050
I would trade these as a set for a 32" or bigger b&c in Stihl large mount.

 

[TRI955]

Bunch of parts for the 272/268/66 type.

Have a good 272 cylinder??

 

[Kwdog75]

Crankcases, cylinder, small parts galore for the 372. No gas tanks Two full wrap handlebars that have been hit by the chain quite a few times but still hanging in there.

Got pictures of the full wrap handlebars?

 

[Jacob J.]

Mike- I could use a 394 cylinder.

 

[rupedoggy]

OK guys got a little back log on this stuff right now. Several interested. Jacob J. has the 153 and 394 cylinder spoken for. The other items are still availabe but there are some pictures going out and dealing going on. I have pictures of the 031 and 041 but am still digging on the 268 type stuff and 288 type stuff. The 031 is complete and even some of the rubber mounts good but it has low compression (100#). The rest of it is good and not broken, cracked or even faded. Mike

 

[2000ssm6]

OK guys got a little back log on this stuff right now. Several interested. Jacob J. has the 153 and 394 cylinder spoken for. The other items are still availabe but there are some pictures going out and dealing going on. I have pictures of the 031 and 041 but am still digging on the 268 type stuff and 288 type stuff. The 031 is complete and even some of the rubber mounts good but it has low compression (100#). The rest of it is good and not broken, cracked or even faded. Mike

I'd like to have a good oem 066/660 cylinder if ya got one, a matching p&c would be even better. I got green to trade.

 

[wigglesworth]

I have a David Bradley gear drive with the AH81 powerhead. Good comp and spark but the flywheel is cracked and the recoil is missing Should be an easy fix for somebody with parts, or good parts to fix up another AH81 powered saw. Anyways, its taking up space, and I dont seem to be finding any parts, so its up for grabs. Will trade for ??? or $$$

 

[Jacob J.]

I have a David Bradley gear drive with the AH81 powerhead. Good comp and spark but the flywheel is cracked and the recoil is missing Should be an easy fix for somebody with parts, or good parts to fix up another AH81 powered saw. Anyways, its taking up space, and I dont seem to be finding any parts, so its up for grabs. Will trade for ??? or $$$

I just happen to have an extra AH-81 motor and recoil assembly. What are you looking to get for it?

 

[2000ssm6]

390 XP that has been woods ported, shaved and dual ported. Trade for a 660 that is full wrap in good condition. Stock or modded. Just not beat up. My 390 has 4 months of work time, but is in good shape. I am a stickler on airfilter maintance and replacement. Just put a new one in. I change them every other month or every month in the heat.

Might want to check with Jasha. Last I heard he was getting rid of all his 660s, that was awhile ago though.