Swap meet...

[SawGarage]

I gotcha...

the NV in my truck usually only gets shifted (using the clutch) when taking off... unless i need to MOVE QUICKLY.

understand the coin thing I'm in the same boat, got a cam Change in the TDI Jetta, and a BUNCH of stuff to do on the truck (front seal, carrier bearing, trans is leaking, etc...ugh.)

I need to sell some saws too!! maybe some saw parts also!

good luck!!

Jay

 

[SugCutter]

Stihl 045 AV

I have a Early (Points Ignition 72?) Stihl 045 AV with a 20" duromatic and a Stihl RM chain that I just rebuilt from the crank up. New seals, bearings, fuel and impulse lines, AV mounts and tilly rebuild. Saw runs great (1 tank through the saw so far), but the durn thing is just to heavy for these old arms. I think that a 034/036 saw would better fit my needs and would consider trades for a project saw or ?
PM interest and offers.
Thanks,
Sug

 

[lwn9186]

I still have some old relics I need rid of, I'm selling the diston, the pm universal, the Mac 940 and mc91 parts my David Bradley a Mac 250 a hommie c51 or two I also have some 025 parts need it gone asap because the tranny let go In my cummins

What 025 parts do you have?

 

[oscar4883]

Still looking for an 036 muffler in nice shape. Also need a air filter cover for an 044. As long as its not cracked in half its good enough for me. Have some parts and cash to swap.
Thanks
John

Also need the screw and metal guard for the corner of the gas tank on an 044.

 

[Mastermind]

Needing a coil for a Stihl S-10.

 

[atpchas]

I have a pretty rough cover (1128 141 0500).
It's missing the knob. The pic shows the bad side.

Yours for the postage.

Charlie

Still looking for an 036 muffler in nice shape. Also need a air filter cover for an 044. As long as its not cracked in half its good enough for me. Have some parts and cash to swap.
Thanks
John

Also need the screw and metal guard for the corner of the gas tank on an 044.

 

[Teddy.Scout]

I have 6 loops of Carlton chain
3/8 .063 84DL

Need want
066 carb.
066 rim drive sprocket
070-090 clutch cover
3003 stihl bar 18-24" (don't care about looks)

 

[schmuck.k]

husky 390 xp

looking for a husky 390xp if any one wants to sell one pm me

 

[SawGarage]

I have 6 loops of Carlton chain
3/8 .063 84DL

Need want
066 carb.
066 rim drive sprocket
070-090 clutch cover
3003 stihl bar 18-24" (don't care about looks)

ah, thou hath a memory that besiges oneself...

 

[Teddy.Scout]

ah, thou hath a memory that besiges oneself...

Lines are open!

 

[mrinds]

Echo cs 440

Anyone got the short block for the cs440. Need both the piston and cylinder. Thanks
Best Regards / Mike

 

[wigglesworth]

Long shot, but does anybody have any AH81 parts. I need basically a whole bottom end, but a set of case half's might get me by. Not sure what I have to trade, but I got lots of junk.....

 

[DaltonPaull]

051/075/076 muffler

I'm looking for a muffler for my 075 with the curved recess for clutch clearance. Reference this thread if your not sure: http://www.arboristsite.com/showthread.php?p=2409872#post2409872

I'll trade you an 066 ignition for it or??

 

[cat-face timber]

I'm looking for a muffler for my 075 with the curved recess for clutch clearance. Reference this thread if your not sure: http://www.arboristsite.com/showthread.php?p=2409872#post2409872

I'll trade you an 066 ignition for it or??

PM Sent

 

[dragrcr]

What 025 parts do you have?

I have basically a whole powerhead minus starter cover I'm gonna keep the b/c

 

[jockeydeuce]

Needing a coil for a Stihl S-10.

If it's the same as an 08S with points, I might be able to help you.

 

[Mastermind]

If it's the same as an 08S with points, I might be able to help you.

I can surely find out...... Thanks

 

[Mastermind]

I can surely find out...... Thanks

By looking at the ILP and the service manual it is the same.

 

[jockeydeuce]

By looking at the ILP and the service manual it is the same.

PM sent.

 

[tlandrum]

i am in need of a 288 deflector preferably the large one with screen