Swap meet...

[MS460WOODCHUCK]

Here is a list of parts that I'm needing...

290/310/390 P/C
Bucking spike for a poulan 3400
24 or 28'' bar for a PM 700
Older style NON chain brake clutch cover for a mac 10-10 or any other model that will work
Bucking spike's for a mac 10-10, 7-10 or PM700
Poulan 4000 P/C
Good running mac 7-10
Good condition mac 7-10 or PM 700 P/C

and a list of stuff to trade or sell...

Complete homelite SXL AO that pulls 150 on the comp guage starts right up but dies in the cut.
Complete poulan 306A that fires up but is low on compression
Complete good running poulan 245A that pulls 145 on the comp guage
Dayton/poulan 3400 that is very clean and good running pulls 150 on the comp guage
MS290 that is a very clean saw with bad P/C (saw will still start)

PM me if you have or are interested in something.

 

[roncoinc]

I need a gas cap with silver insert intact for this Mighty Mite Auto I restored. Normally I don't think I'd care but this is perfect now otherwise-
Also still need Stihl 048/042 air filter.
I won't list a mess of trade stuff as I'm new enough to this I don't have too much yet. I do have green and Paypal $ though . Thanks!
John H.

A cap like this one ?

 

[sefh3]

I need a gas cap with silver insert intact for this Mighty Mite Auto I restored. Normally I don't think I'd care but this is perfect now otherwise-

Also still need Stihl 048/042 air filter.

I won't list a mess of trade stuff as I'm new enough to this I don't have too much yet. I do have green and Paypal $ though . Thanks!

John H.

Is this what your looking for? I have two styles one male thread and one female thread. Both have Mix 16:1 on them. Can't figure this new camera out so it takes a pictures of the the writing on the silver tabs.

 

[roncoinc]

Dolmar air filters needed

Looking for air filter for a dolmar 111
also for a 6000i
have stuff.
stihl 020av with bad p&c.
homie XL stuff.
junk and more stuff.etc..

 

[sefh3]

Here is a list of parts that I'm needing...

290/310/390 P/C
Bucking spike for a poulan 3400
24 or 28'' bar for a PM 700
Older style NON chain brake clutch cover for a mac 10-10 or any other model that will work
Bucking spike's for a mac 10-10, 7-10 or PM700
Poulan 4000 P/C
Good running mac 7-10
Good condition mac 7-10 or PM 700 P/C

and a list of stuff to trade or sell...

Complete homelite SXL AO that pulls 150 on the comp guage starts right up but dies in the cut.
Complete poulan 306A that fires up but is low on compression
Complete good running poulan 245A that pulls 145 on the comp guage
Dayton/poulan 3400 that is very clean and good running pulls 150 on the comp guage
MS290 that is a very clean saw with bad P/C (saw will still start)

PM me if you have or are interested in something.

Will this bar fit your PM700....31" total length.

 

[MS460WOODCHUCK]

Will this bar fit your PM700....31" total length.

I don't know for sure, I'm not used to these macs and I can't make out the #'s on the bar in the pic. If it does I'm interested. Is it good and straight with true rails? What guage is the kerf>

Can anyone on here tell me if it will fit the PM700?

 

[Modifiedmark]

Here is a list of parts that I'm needing...

290/310/390 P/C
Bucking spike for a poulan 3400
24 or 28'' bar for a PM 700
Older style NON chain brake clutch cover for a mac 10-10 or any other model that will work
Bucking spike's for a mac 10-10, 7-10 or PM700
Poulan 4000 P/C
Good running mac 7-10
Good condition mac 7-10 or PM 700 P/C

and a list of stuff to trade or sell...

Complete homelite SXL AO that pulls 150 on the comp guage starts right up but dies in the cut.
Complete poulan 306A that fires up but is low on compression
Complete good running poulan 245A that pulls 145 on the comp guage
Dayton/poulan 3400 that is very clean and good running pulls 150 on the comp guage
MS290 that is a very clean saw with bad P/C (saw will still start)

PM me if you have or are interested in something.

John, you interested in another 10-10 since your leaning towards the yellow ones now days? I got a nice one, may trade it and some other stuff for the 245. I could probably come up with a bar and spike.

 

[SawGarage]

I don't know for sure, I'm not used to these macs and I can't make out the #'s on the bar in the pic. If it does I'm interested. Is it good and straight with true rails? What guage is the kerf>

Can anyone on here tell me if it will fit the PM700?

Hey John,

i'd be willing to bet it would. I don't recall oo many Mac mounting patterns (other than the PM1000/Partner saw)

if not, I ave a 24, and I think a 26' bar for ya avail. 050 ga is standard for mac's IIRC.

J

 

[tomdcoker]

Power Mac 6

I bought one this week that is cosmetically good and I need some parts. I need a brake band, a pull handle and probably a P &C. If you have a parts saw with these item's I have parts, cash and paypal. Thanks Tom

 

[wigglesworth]

I could use a Good p&c for a 10-10 mac if anybody has an extra.

 

[parrisw]

I'm in need of the spring for the throttle lever saftey catch, for a 372xp

 

[nmurph]

i need a clutch cover for a 357/359. what i really need are the CB parts, but the whole piece would save me some work!! all of the CB parts were stripped out. all i have is the cover itself.

 

[surfincr]

really need an 031 oiler and clutch just the shoes and springs if possible

also looking for an 045 chain brake setup (cover, band, hand guard etc)

 

[SawGarage]

I could use a Good p&c for a 10-10 mac if anybody has an extra.

Wigs...

I saw you needin somethin else recently...what was it? (past day or two...)

my back button doesn't work :monkey: lol

I'm in need of the spring for the throttle lever saftey catch, for a 372xp

presence lever spring - (should be) check.

next?

 

[54stude]

McCulloch bar trade wanted.

I have a used windsor 36" .404 speedtip bar for "mid sized" McCulloch mount I think, the bar says b03x 3816 36tmx63sn.

I would like to trade it for a 32-36" roller tip bar for "big" McCulloch saws, like 790/795/797.

Anyone interested?

 

[volks-man]

hey folks!
i needs a carb screw grommet for the air filter cover on 034/036.
stihl calls it: guide 1125 121 7700

i have some odds and ends for 020av and 038 and green.

thanks-----------

 

[tlandrum]

hey folks!
i needs a carb screw grommet for the air filter cover on 034/036.
stihl calls it: guide 1125 121 7700

i have some odds and ends for 020av and 038 and green.

thanks-----------

if you can get me a pic of the grommet i may have one

 

[Duke Thieroff]

Up for trade, for other saws possibly.

Fair cosmetic shape, has spark, somewhat weak and gets gas. Piston looks rough and might need a new one sooner than later.

Let me know what you got!

Pulling just shy of 120lbs of compression, bumping it up


CT

 

[350jeepcj5]

I am in need of a 10-10 clutch cover, and a 100cc project saw

 

[volks-man]

hey folks!
i needs a carb screw grommet for the air filter cover on 034/036.
stihl calls it: guide 1125 121 7700

i have some odds and ends for 020av and 038 and green.

thanks-----------

if you can get me a pic of the grommet i may have one

rats! i don't even know what it looks like. my cover came without one.
i can see a small pic of it in mediacat, but i don't think i can post a pic from mediacat.

anyone got a pic of the grommet for me?