Swap meet...

[tomdcoker]

Stihl and McCulloch

I have an 07S that I am trying to rebuild and need the rubber mounts on the bottom of the saw. Part # 1107-021-7600.
Also I have two volumes of the McCullloch Service Bulletin volume four and one copy of volume five. I would be interested in trading a volume four copy for a volume that I do not have. Thanks for any help. Tom

 

[NeoTree]

I'm still in need of some 046 parts.
I'm looking for about 24" of handle bar wrap, it seems to be 22mm diameter, compression release plug p/n 1122 025 2200, air baffle p/n 1128 141 6300, and carb flange p/n 1128 120 2202. I'm just hoping sombody has a big roll of the handlebar wrap and can slice me off a chunk.
To trade I got lots of 045/056 stuff, a velocity stack carb flange for an 046, a complete tiny older craftsman that has erratic spark and won't start, and $$.

 

[Modifiedmark]

I have a idea going around in my pea sized brain. If I put a point coil and bracket on with a Atom module to replace the points, that would work... yes???

Yes I did that on a Super XLA and it works fine. Be sure to check the flywheel to make sure there the same though. They maybe timed different and if so you could use the point flywheel as well.

I can't say for sure as I used the bracket and coil from a XL400 on mine and the SXL electronic flywheel.

 

[tlandrum]

I'm still in need of some 046 parts.
I'm looking for about 24" of handle bar wrap, it seems to be 22mm diameter, compression release plug p/n 1122 025 2200, air baffle p/n 1128 141 6300, and carb flange p/n 1128 120 2202. I'm just hoping sombody has a big roll of the handlebar wrap and can slice me off a chunk.
To trade I got lots of 045/056 stuff, a velocity stack carb flange for an 046, a complete tiny older craftsman that has erratic spark and won't start, and $$.

what do you need for the velocity stack,i may have a good carb flange. i try and keep a spare or two as they get brken easy enough

 

[Mastermind]

Yes I did that on a Super XLA and it works fine. Be sure to check the flywheel to make sure there the same though. They maybe timed different and if so you could use the point flywheel as well.

I can't say for sure as I used the bracket and coil from a XL400 on mine and the SXL electronic flywheel.

We have three SXLAOs only one has a good coil. I enjoy using these old saws and want to get them going again. Thanks for the help guys.

 

[NeoTree]

what do you need for the velocity stack,i may have a good carb flange. i try and keep a spare or two as they get brken easy enough

I'm actually switching from a velocity stack to the Max Flow setup so I'm looking for the stock flange.

 

[schmuck.k]

Will check to see what I have left. Don't think I have any plastic though, couple pistons, crank and other misc.

thanks

 

[SawGarage]

How many coils would you like? Blue or black? IF I remember right, a 385 muffler will fit? Better check into that, I have one if it works.

Hey Mitch...lol, after ONE box just left

I'll say 2 for now (preferably both black)...I have two to test, but told they were bad...I need ATLEAST 3 good coils.

385 Muffler will fit, yep.

tell me what you need

THANKS MAN!!!!

Jay

I would like a black one.....

SHOOOOO wigs, shooo!!!! buzz off

 

[epicklein22]

I'm still in need of some 046 parts.
I'm looking for about 24" of handle bar wrap, it seems to be 22mm diameter, compression release plug p/n 1122 025 2200, air baffle p/n 1128 141 6300, and carb flange p/n 1128 120 2202. I'm just hoping sombody has a big roll of the handlebar wrap and can slice me off a chunk.
To trade I got lots of 045/056 stuff, a velocity stack carb flange for an 046, a complete tiny older craftsman that has erratic spark and won't start, and $$.

You should be able to buy that wrap at the dealer. Or you could wrap it with bicycle handlebar tape. It works surprisingly well. I should have an extra decomp laying around too. I plug all of mine.

 

[slipknot]

wanted Mcculloch 10-10 parts saw

Hello I have a early mac 10-10s that I am doing a full rebuild/restoration on. I am in need of a later model(chain brake) 10-10 parts saw. I need a rear handle/tank and might need a crank...as the one i have the key way is boogered up. If anyone has a 10-10 or a 10-10s parts saw they are going to junk out or just want to get rid of for fairly cheap please PM me.

 

[Mastermind]

You should be able to buy that wrap at the dealer. Or you could wrap it with bicycle handlebar tape. It works surprisingly well. I should have an extra decomp laying around too. I plug all of mine.

Two layers of large heat shrink tubing works fairly well too.

 

[mweba]

Hey Mitch...lol, after ONE box just left

I'll say 2 for now (preferably both black)...I have two to test, but told they were bad...I need ATLEAST 3 good coils.

385 Muffler will fit, yep.

tell me what you need

THANKS MAN!!!!

Jay








SHOOOOO wigs, shooo!!!! buzz off

Hey play nice guys

I only have a couple unlimited coils but many blue ones. Will send em out next week.

Let me know wiggs

 

[SawGarage]

hey play nice guys

just foolin wigs!!!!! :jester: oke:

 

[ThePruner]

:greenchainsaw:

 

[DSS]

I have a idea going around in my pea sized brain. If I put a point coil and bracket on with a Atom module to replace the points, that would work... yes???

THAT I do have, point coil and flywheel. Let me know. I could use a large mount husky bar, circa 20-24'' if anyone has one laying around.

 

[JohnnyBoy1986]

Poulan 245A

I am in need of a good piston and cylinder for a Poulan 245A. I would prefer to have new if the price was right but a good used assembly would do just fine as well. Please PM me. Thanks

 

[roncoinc]

We have three SXLAOs only one has a good coil. I enjoy using these old saws and want to get them going again. Thanks for the help guys.

I got after market modules if you need one.

 

[slipknot]

Hello I have a early mac 10-10s that I am doing a full rebuild/restoration on. I am in need of a later model(chain brake) 10-10 parts saw. I need a rear handle/tank and might need a crank...as the one i have the key way is boogered up. If anyone has a 10-10 or a 10-10s parts saw they are going to junk out or just want to get rid of for fairly cheap please PM me.

I have a mcculloch 3.4/timberbear in good running/woodcutting condition that i would trade for a later model 10-10 thats in like condition.

 

[slipknot]

I have a mcculloch 3.4/timberbear in good running/woodcutting condition that i would trade for a later model 10-10 thats in like condition.

I must add that it must have elctronic ignition...i need the flywheel too...i got a busted fin.

 

[Scandy14]

Still looking for a coil for a Stihl 191T. Don't have anything to trade except some $$.