Swap meet...

[Evan]

im looking for 044 parts,
air filter cover HD
top cover
air filter.
clutch
hub bearing.
piston
cylinder
mufflers.

pm if you have anything

also would consider tradeing my 084 for a 460 in very good shape

 

[Sawdustmaker]

hey even you could have sent me that list.... hehe

ill pm you what i have.

 

[brokenbudget]

skil 1645, runs well, one of the muffler bolt holes are stripped, needs fuel lines to run perfect. of course, the starter needs to have a good pull on it to crank the engine over (starter cup worn). no bar/chain.

28'' stihl (large mount) bar with 3/8'' stihl chain. got this off of an 064, slight rust on chain but all in good shape. chain will need to be sharpened before use.

poulan 3400 piston, rings, cylinder, good shape.
air filter for above saw, (new) will fit the 3700 as well. i have more parts from this saw.

looking to trade parts or whatever.... whatcha gots??

 

[epicklein22]

skil 1645, runs well, one of the muffler bolt holes are stripped, needs fuel lines to run perfect. of course, the starter needs to have a good pull on it to crank the engine over (starter cup worn). no bar/chain.

28'' stihl (large mount) bar with 3/8'' stihl chain. got this off of an 064, slight rust on chain but all in good shape. chain will need to be sharpened before use.

poulan 3400 piston, rings, cylinder, good shape.
air filter for above saw, (new) will fit the 3700 as well. i have more parts from this saw.

looking to trade parts or whatever.... whatcha gots??

How is that bar a large mount if it came off a 064. The large mount fits the 090,088, 084, 076, 075, 070, 051, 050 only.....did it have spacers?

 

[barneyrb]

I am in need of a 480CD muffler. Got some homelite, poulan, cash, and stihl stuff.

 

[KTM640]

Looking for an 066 case in good shape for my redlight. When I got the saw it was missing a few chunks and the upper inner spike was broken off. Would like to make it respectable again.

I've got 064/066 parts (clutch, oil pump, chain adjuster, etc) and a 021 handle for trades.

pm me if you have something

 

[Modifiedmark]

Mac 2-10

Anyone want this Mac 2-10 before I ebay it? I'ts been sitting for a while, got lots of compression and I got it to spark a couple times, but it's got a broken starter pawl, so I didn't crank it much.

PM, me your ideas..

 

[brokenbudget]

How is that bar a large mount if it came off a 064. The large mount fits the 090,088, 084, 076, 075, 070, 051, 050 only.....did it have spacers?

i could be wrong on this, i'm just going by what the dealer guy i got it from said. "steped mounting bolts, so you need to use a large mount bar"...
the stud groove is rather large.

 

[Sawdustmaker]

large being 3003 not small 3005

or 3002

 

[brokenbudget]

large being 3003 not small 3005

or 3002

i'll check tonight when i get home for the proper numbers.

 

[Trigger-Time]

3002 is Large mount

 

[JONSEREDFAN6069]

Any one got a set of big dawg's for an 066. I have a 630 parts saw missing the coil, muffler, bad piston, no recoil or clutch cover.
Have a mac 610 & 310 pretty much complete, neither run. A echo
evl-650 has spark and but no gas needs a carb kit, no bar.

 

[gregz]

I need a chain catcher for a stihl 056,prefer new. stihl part number
1117 656 7700 I ordered one from the dealer months ago still on back order
cheers
gregz

 

[Harzack223]

Hello all, I am looking for a stihl 048 running or not, in decent condition don't want to have to put a couple hundred into it. I may have some saws I can trade for it or towards it. Thanks, Josh

 

[Bowtie]

Looking for an 066 case in good shape for my redlight. When I got the saw it was missing a few chunks and the upper inner spike was broken off. Would like to make it respectable again.

I've got 064/066 parts (clutch, oil pump, chain adjuster, etc) and a 021 handle for trades.

pm me if you have something

I have an 064 case and crank in useable shape. I am not sure if the case is the same, but I do have a bare case, without bearings, and a good crank.

 

[Madsaw]

Hello all, I am looking for a stihl 048 running or not, in decent condition don't want to have to put a couple hundred into it. I may have some saws I can trade for it or towards it. Thanks, Josh

I got a 048 super here. Not the nicest looking saw. Clutch cover is rough. It does start and run but kill switch is not working. Did nto run it long enough to see how good it runs.
What do you have to trade?
Bob

 

[Bill G]

I got a 048 super here. Not the nicest looking saw. Clutch cover is rough. It does start and run but kill switch is not working. Did nto run it long enough to see how good it runs.
What do you have to trade?
Bob

Bob,

I will PM you in a minute or 2,

Bill

 

[Madsaw]

Bob,

I will PM you in a minute or 2,

Bill

Pics on there way later today Bill.
Bob

 

[bopop]

MS 290 Need Gas Tank

I need a Gas Tank for a Stihl MS290. Falls and only thing that breaks is gas tank.

 

[BlackCatBone]

I have an Oregon Mini chain grinder for sale or trade. Comes with all the original stuff and extra 3/16th wheel and original box. Trade bait, or $100 shipped anywhere in the conus. I bought a Silvey machine and don't need this one too.

Thanks