Swap meet...

[lwn9186]

In need of an outer muffler cover and fuel cap for a Echo CS371 or John Deere 40v.
Have some Stihl parts or green for trade.

 

[epicklein22]

Anybody have a cylinder for a 261/262xp?

Many parts and $ for trade....

 

[hamish]

High top or low for the 372?

prefer a low top.

 

[firefighter33]

A friend of mine is looking for 066 plastic he is missing both the top cover and air filter cover. He need a top cover with decomp.
Im also going to be looking for 066 parts have one on the way:hmm3grin2orange: Not sure what i need yet Top End for sure but will probably go with BB kit unless someone has a stock one cheap?

 

[blsnelling]

Anyone have a 066 crankshaft for metal flywheel with the larger 13 needle big end rod bearing, PH 1122 030 0407?

 

[bigblockburris]

Echo/John Deere

Lawn9186,

What number Echo/John Deere is this?
This is a fresh barn find!!! LOL!!
Sorry pic is small.

 

[DSS]

Lawn9186,

What number Echo/John Deere is this?
This is a fresh barn find!!! LOL!!
Sorry pic is small.

451 I think..

http://acresinternet.com/cscc.nsf/e...f19c577082353baf88256d0c006cc5a2?OpenDocument

Look under the clutch cover, just ahead of the sprocket by the chain catcher, there should be a plate with ''kioritz'' and a model number on it.

 

[lwn9186]

Lawn9186,

What number Echo/John Deere is this?
This is a fresh barn find!!! LOL!!
Sorry pic is small.

It has one extra screw holding the recoil on so it must be something other than a 40v.

 

[bigblockburris]

John Deere

After a liitle research, it is a Echo 452.

Anybody want it?

 

[leeha]

Hi, Looking for a Piston and Cylinder for a Jonsered 920.
I have 2 910 Cylinders to swap or cash. Must be in nice
condition.

PM me if you can help.

Thanks Lee

 

[atpchas]

Hello to everyone what a great site! I have 084 that I have rebuild with oem parts. I am needing a muffler new or used in good condition. I have 2 brand new outer casing so if someone atleast had inner part of muffler. My research has let me know that it is NLA thru Stihl. Any aftermarket mufflers??? Call Scott @
816-719-9547 if you can help

I have a muffler with 1124/05 on the side. I think that makes it 084/088, but I don't know if there were multiple versions. I got the muffler in a box of random parts, so I have no idea exactly what it came off. It is not shiny and new but it is structurally sound. If you're interested, send me a PM and I can send you a picture or two.

Charlie

 

[Modifiedmark]

I would be interested in Poulan 14" bow setup if someone has one to part with.

 

[Duke Thieroff]

Looking for a bar that will fit a mac 610, .050 70DL

Chris

 

[zogger]

maybe?

I got a Partner 500 that I'm needing chain brake parts for.

I have a 400 in rough shape as a saw, it's a hulk and locked up,major parts missing, but the chain brake assembly looks complete and functional. The decal has one tiny tear in it. Will this fit your saw? If so and you want it, PM me, I got a few pics I just took.

 

[Arrowhead]

I have a 400 in rough shape as a saw, it's a hulk and locked up,major parts missing, but the chain brake assembly looks complete and functional. The decal has one tiny tear in it. Will this fit your saw? If so and you want it, PM me, I got a few pics I just took.

I'm not sure, pm sent.

 

[67L36Driver]

12" (?) Homie bar for XL

Old bar measures 12 1/2" O.A.L. Hard nose, .050". Chain is 42 DL x 3/8"P x .050". Good chain!

View attachment 172267
Nose is shot and DLs are dragging the bottom of the groove.
Been all over Baileys and found nutin'.

Got a lead?

 

[Eccentric]

Looking for a bar that will fit a mac 610, .050 70DL

Chris

Hiya Chris,

May have one of those for you. Came off an Echo CS451VL. Same bar mount IIRC. It's an Oregon 'banana' curved-tip sprocket nose though. I'll double check the length and DL count if you're interested. May have a loop of chain for it too. You could consider it a 'partial payment' for that 011AV!

Also have a 28" cut lenght bar and a loop of .404 chain for the X-10/PM700/CP81/etc saws that I could send you with it. That'd get me close to being even methinks. Just a thought...

Edit:Just remembered that the 28" bar is a hardnose and has a small bit of the rail chipped out of it. Hasn't affected the performance of it, but it is there. Could send you a pic. It is a nice pretty lookin' earlier grey/black PM bar...

Old bar measures 12 1/2" O.A.L. Hard nose, .050". Chain is 42 DL x 3/8"P x .050". Good chain!


Nose is shot and DLs are dragging the bottom of the groove.
Been all over Baileys and found nutin'.

Got a lead?

The shortest bar that Baileys lists for that saw is 12"/48DL (with a 12.5" overall length and 42DL, your old bar is a 10" cut length).

Here are the 12" bars listed on Baileys.

http://www.baileysonline.com/itemdetail.asp?item=ORF+120DGEA061&catID=

http://www.baileysonline.com/itemdetail.asp?item=ORF+120GPEA061&catID=

If you really want to reuse that chain and run a 10" bar, then try www.chainsawr.com. Scott is a site sponsor, and his banner ad is at the top right of the screen. Look for the brown banner with the red chainsaw on it. I believe I saw both used and new bars for that saw on his site. Can't remember if any of 'em were 10" though. Maybe the used ones. Otherwise, I'd suggest going to www.edgeandengine.com (also a site sponsor) for a new bar.

 

[littlelizard1]

Echo 650EVL

piston, and felling dogs? anyone. clams for trade cause I just started this saw thing :smile2:

 

[Duke Thieroff]

Hiya Chris,

May have one of those for you. Came off an Echo CS451VL. Same bar mount IIRC. It's an Oregon 'banana' curved-tip sprocket nose though. I'll double check the length and DL count if you're interested. May have a loop of chain for it too. You could consider it a 'partial payment' for that 011AV!

Also have a 28" cut lenght bar and a loop of .404 chain for the X-10/PM700/CP81/etc saws that I could send you with it. That'd get me close to being even methinks. Just a thought...

Take a look at that 20inch bar you got, I already have 4 loops of chain that will fit a 70 link .050 bar for my 610 and my PM700.

Been switching bars back and forth, which ain't no way to live.

I sent all my bars down to Virginia in a trade, and probably should have held one back, just in case.


Shoot me a PM and we'll hash it out

Chris

 

[Duke Thieroff]

Looking for a tank vent for a Husky 480CD

Anyone got one?


Chris