Swap meet...

[SugCutter]

Homelite 20" Bar

Homelite History Still Available

I have a very nice Homlite 20" Bar that I don't have any use for.
The bar was purchased for a Homlite 360 many moons ago. I believe that it will also fit XL saws. 20" .375 x .050 11 tooth sprocket nose.
Takes a .375 x .050 70 DL chain.
Looking to swap for comparable Stihl 16" 3003 .325 x .063 bar OR a Husqvarna small mount (Husq 51) 16".375 x .050 Bar
PM any interest
Sug

 

[oscar4883]

Anyone have a set of the emormously oversized dawgs for a 064/066? I am looking for something bigger than the large stockers to use on my stumpin saw.

 

[JoshF]

How big are the dogs that madsens has? I think they make them.

 

[Guido Salvage]

Need Homelite 540 help!

My almost new Homelite 540 took a tumble off my rolling storage cart and the rear handle is no more. I bought the saw new and think I have only run 2 tanks through it. Can anyone help with a tank assembly to get me going before the Virginia GTG next month?

Have some green and a bunch of stuff I can trade...

 

[nmurph]

can't help, but that must have been an awful moment!!!!!!!!!!! i bobbled a 346 cylinder yesterday. i somehow managed to juggle it in the air until i could get my hands on it.

 

[Guido Salvage]

Old bar measures 12 1/2" O.A.L. Hard nose, .050". Chain is 42 DL x 3/8"P x .050". Good chain!

View attachment 172267
Nose is shot and DLs are dragging the bottom of the groove.
Been all over Baileys and found nutin'.

Got a lead?

I may have one of those, I will need to check. I will look here tomorrow, if I do not have it there is a possibility I have it at my other place in a box of junk XL's and Super 2's, but it will be a while before I can check.

 

[67L36Driver]

I may have one of those, I will need to check. I will look here tomorrow, if I do not have it there is a possibility I have it at my other place in a box of junk XL's and Super 2's, but it will be a while before I can check.

That's cool. Per mr. Eccentric it is a nominal 10" bar and not a 12 like I thought.

 

[Guido Salvage]

I think there's a 540 on eBay right now.

There is and I am watching it, but rather than buy a complete saw I was hoping to piece this one back together.

 

[bcorradi]

I'm looking for a nice MS660 starter cover. I have parts and cash to trade.

 

[roncoinc]

Needed , husky 365 starter.
to go away, husky 365 p&c in good shape.

 

[Kwdog75]

prefer a low top.

I have a dirty low top, PM me with your info.

 

[HittinSteel]

Anyone with a 372 piston and ring laying around collecting dust? If not I'll grab a Meteor from Baileys

 

[STIHL880]

Well, I'll throw my name out there, Does anyone have a used MS 260 sitting around? I got a husky 61 rancher that I can trade, (needs a new top end i think)
The 260 doesn't need a bar and chain. But i'll gladly pay a little extra for a 20" bar, Let me know guys, I'm really on the hunt for one now..

 

[Eccentric]

That's cool. Per mr. Eccentric it is a nominal 10" bar and not a 12 like I thought.

Yep. Your saw would have originaly been listed as an XL-10. Unless you get lucky and find a good used 10" cheap, you're probably money ahead replacing that bar and chain with a 12" set (new or used). A nominal 12" bar would be 14.5 or so inches long and take a 48DL loop of 3/8"LP.

 

[kev1n]

Hey Eccentric, I was reading your wants on the bottom of your page. I have a really nice super e-z with a toasted piston if you want it. I also have a couple really nice used 16" and 18" bar and chain combo's for said saws if interested.
Kevin

 

[MS460WOODCHUCK]

Still looking for a 2149 turbo top cover. Also looking for a coil from a husky 50, 51, 55, 61 and a 268. I have a few things to trade or a little green.

 

[Arrowhead]

Still looking for a clutch cover with brake, or just the brake parts for a Partner 500/5000 or Jred 490/590. I have a good brake lever.

 

[MS460WOODCHUCK]

Still looking for a 2149 turbo top cover. Also looking for a coil from a husky 50, 51, 55, 61 and a 268. I have a few things to trade or a little green.

Just bumping to the top of the page.

 

[kev1n]

I've got a nice Pioneer P50 case with recoil. I'm looking for everything else needed to get this project together or a parts saw.

bottom handle
top handle
air filter cover
anti vibe bushings
clutch cover
bar nuts

I have stuff to trade or some clams.
Thanks Kevin

 

[epicklein22]

Just bumping to the top of the page.

Do you have a jred dealer near by? If you don't, I'm sure someone can order you a new one. I doubt they cost that much.