Swap meet...

Rugged made
Wesspur
Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
cbolyard said:
I have a Stihl MS460 for parts or to fix. Missing a handlebar, oiler, bar and chain. It has an 064 chain brake handle on it that doesn't engage the chain brake, but all the parts for the chain brake are there and work like they should. There are a couple pieces missing from the clutch cover (long style) and a small crack in the air filter cover. I bought it with the intent of fixing it up but the wife won't let me spend any money on it. I have opened up the factory port on the muffler and cleaned the saw up some, but that's about it.
Click to expand...

What are you looking for in trade?
 
heimannm said:
I am desparate for the duck bill valve to go in the 10 Series McCulloch carburetors, part number 63041. I would like to get 4 or 5 if possible.

.
Click to expand...
What is the duck bill valve ? I have a couple drawers with mostly new McCulloch parts. Mabe there is 1 if I know what to look for. Sold most what fit the pm700.
I bought an PM 805 this weekend not running. Looks decent. I haven't checked it out much but the handle bar wasn't assembled right on the bottom and I am guessing a previous owner had it off to get at the exhaust to view the piston and cylinder for damage. Had old spoiled gas in it also. I might be looking for parts to fix it with or might be willing to trade . I need a good ms 440 tank-rear-handle-housing + a few other 440 parts. Might trade for a + 60 cc Stihl or Dolmar.
 
cbolyard said:
I have a Stihl MS460 for parts or to fix. Missing a handlebar, oiler, bar and chain. It has an 064 chain brake handle on it that doesn't engage the chain brake, but all the parts for the chain brake are there and work like they should. There are a couple pieces missing from the clutch cover (long style) and a small crack in the air filter cover. I bought it with the intent of fixing it up but the wife won't let me spend any money on it. I have opened up the factory port on the muffler and cleaned the saw up some, but that's about it.
Click to expand...

:popcorn: I think we all are wondering.
 
Brushwacker said:
What is the duck bill valve ? I have a couple drawers with mostly new McCulloch parts. Mabe there is 1 if I know what to look for. Sold most what fit the pm700.
I bought an PM 805 this weekend not running. Looks decent. I haven't checked it out much but the handle bar wasn't assembled right on the bottom and I am guessing a previous owner had it off to get at the exhaust to view the piston and cylinder for damage. Had old spoiled gas in it also. I might be looking for parts to fix it with or might be willing to trade . I need a good ms 440 tank-rear-handle-housing + a few other 440 parts. Might trade for a + 60 cc Stihl or Dolmar.
Click to expand...

Brushwacker - The duck bill valve PN 63041 is a small, black rubber valve very similar to the one in the fuel cap of the bigger McCulloch saws (200/250/300 etc.) but much smaller diameter. It is part of the primer circuit in the small McCulloch carburetors.

Mark
 
I have a little Mac 6 that runs like a top but it has a 1/4'' clutch sprocket and would like to switch over to low pro 3/8 can anyone help me out.
 
I need:

015 front handle
015 throttle safety lever
015 air filter

038 tank/handle assy

Stihl BG/HS/FS/FC 72/74/76 piston. They're all the same.

I have:

lots of parts, mostly for 70cc and smaller saws. Some NOS stihl.
 
heimannm said:
I am desparate for the duck bill valve to go in the 10 Series McCulloch carburetors, part number 63041. I would like to get 4 or 5 if possible.

Bob Johnson doesn't have any and neither does the crew of Discount Marine.

Help!

Mark

I have lots of big McCulloch stuff as well as $$ if necessary.
Click to expand...


Mark,
I will go surfing in the boxes of parts and see what I can find.
Bob
 
B200Driver said:
I need:

015 front handle
015 throttle safety lever
015 air filter

038 tank/handle assy

Stihl BG/HS/FS/FC 72/74/76 piston. They're all the same.

I have:

lots of parts, mostly for 70cc and smaller saws. Some NOS stihl.
Click to expand...

I might have a parts bg72 blower, haven't really check it out to see what kind of shape it is in.
 
Sold a homelite super 2 before I cleaned it up and checked it out...:dizzy:...The clutch drum bearing is bad...:cry:...Does anybody have a used drum w/ a good bearing or a torrington B67 bearing laying around...
 
I need an 1118 145 0701 muffler backshell for an 028. It is the earlier one with the bottom mount post on the side
I have 1118 145 0703 backshell that was never on a saw. If someone wants to trade, and lots of other goodies including legal tender.

Also might need an 028 cylinder. P.O. wound oversize self-tapping screws into the muffler mounts on this one........
 
I posted these saws in the trading post,
034 stihl new rings muff mod port polished nice shape 2 bars
450 husky close to new
116si dolmar new rings port polished , muff mod and port matched, good shape
I am just curious to what kind of trades I might get, all saws run great.
 

Similar threads

J
Farmertec Warning
6 7 8
Replies
144
Views
16K
sean donato
sean donato
V
Lots of Questions about Axe Hanging
Replies
3
Views
2K
thomasinvancouver
T
J
Hello!
Replies
9
Views
2K
jackrabbit
J
HumBurner
Sold 181/281 Parts Saws and various NEW parts
2 3
Replies
44
Views
5K
davidwyby
davidwyby
Whiskey_Bravo
What tests would you want to see on a battery powered top handle saw?
2
Replies
33
Views
3K
Dcsco
D

Latest posts

Back
Top