Swap meet...

[huskydude]

2000 2171 jonsered for trade. Starts right up, seems to run well, I just got it.
unlimited factory coil. 130lbs of compression. p/c look to be great. some fins missing from top. chain brake gone.
Few other minor things not perfect. Nice 18" replaceable tip bar and chain with lots of life.
I have one, otherwise I'd rering it and fix it up.

Looking to trade for clean 353 or 346 husky.

View attachment 199119 View attachment 199120 View attachment 199121

 

[MS460WOODCHUCK]

Still looking for a few things guys, hoping someone can help me out. Looking for a few parts for a poulan 3400, choke knob with the wire, inner and outer bar plates, bucking spike and a good rubber AV mount that goes right above the clutch cover towards the back side of it.

Also looking for a 3/8lp clutch rim for a mini mac that belongs to my buddy. He dropped it out of a tree and some how the gear that drives the chain broke off of the rim. :msp_confused:

Got a little to trade and a little cash.

 

[Brushwacker]

Also looking for a 3/8lp clutch rim for a mini mac that belongs to my buddy. He dropped it out of a tree and some how the gear that drives the chain broke off of the rim. :msp_confused:

Got a little to trade and a little cash.

Pretty sure I have the right 1 brand new with a bearing in it P/N 90150 looks like 3/8 lp to me, has a funky looking gear that slightly resembles a rim but is attached to the hub as a unit.
If any body is interested I also have an mcculloch spur sprocket that looks very close to the size of the above 1 but slightly wider and appears to be 1/4 " pitch. Its never been used also, but has a little rust and or tarnish that doesn't look like a problem. P/N 215252 Also I have some loops of 1/4 inch chain new, I have no idea what they fit. It seems to me they were 72dl but I'd need to look for sure.
Have a box w/ some other NOS mcculloch parts , mostly for smaller models I think. Starter springs for I think the bigger late models.
Have some Oregon bars, NOS 18" 095 mt. Husky etc.,
20" 009 mt. Husky etc,
18" & 20" Stihl D025 mt 3/8 pitch.
Would trade for very good sprocket hub or hubs that fit 029,034, 36, 39,ms290,310,390. I don't want a hub more then 50% wore out. Also could use .325 pitch chain,non anti kick, .058 and .063 gauge in new or excellant condition and,or 3/8 primarily semi chisel .050 and .058 gauge.

 

[Modifiedmark]

Pretty sure I have the right 1 brand new with a bearing in it P/N 90150 looks like 3/8 lp to me, has a funky looking gear that slightly resembles a rim but is attached to the hub as a unit.
If any body is interested I also have an mcculloch spur sprocket that looks very close to the size of the above 1 but slightly wider and appears to be 1/4 " pitch. Its never been used also, but has a little rust and or tarnish that doesn't look like a problem. P/N 215252 Also I have some loops of 1/4 inch chain new, I have no idea what they fit. It seems to me they were 72dl but I'd need to look for sure.
Have a box w/ some other NOS mcculloch parts , mostly for smaller models I think. Starter springs for I think the bigger late models.
Have some Oregon bars, NOS 18" 095 mt. Husky etc.,
20" 009 mt. Husky etc,
18" & 20" Stihl D025 mt 3/8 pitch.
Would trade for very good sprocket hub or hubs that fit 029,034, 36, 39,ms290,310,390. I don't want a hub more then 50% wore out. Also could use .325 pitch chain,non anti kick, .058 and .063 gauge in new or excellant condition and,or 3/8 primarily semi chisel .050 and .058 gauge.

John, check those 1/4" loops out closer, I could use some but I think I need 78dl...

 

[Brushwacker]

John, check those 1/4" loops out closer, I could use some but I think I need 78dl...

Hi Mark, There are 3 and they are 6o dl. Stihl RM. When I bought them on ebay I thought they were 3/8 pitch. I probably should keep 1 or 1 and part of 1 in case I need it. I have a carving bar I might use someday. Shouldn't be a problem to fix you up with 78 dl if you have a connecter link to complete the loop.

 

[Modifiedmark]

Hi Mark, There are 3 and they are 6o dl. Stihl RM. When I bought them on ebay I thought they were 3/8 pitch. I probably should keep 1 or 1 and part of 1 in case I need it. I have a carving bar I might use someday. Shouldn't be a problem to fix you up with 78 dl if you have a connecter link to complete the loop.

Thanks John, I have 1/4 pitch connectors. For Oregon


More then likely wont work with Stihl chain.

 

[o8f150]

was wondering if anyone had a good muffler for a 372xp,, the one that is on the saw that i just got yesterday was rusted pretty bad,, the metal is to thin to weld a pipe on,, i have some green and a lot of lint

 

[jerrycmorrow]

olympic 240

recently acquired an Olympic 240 Electronic saw. looking for an air filter, part no. 4000030. got oly and some homie parts (see parts in signature) or some filthy lucre to trade. thanks, jerry

 

[o8f150]

was wondering if anyone had a good muffler for a 372xp,, the one that is on the saw that i just got yesterday was rusted pretty bad,, the metal is to thin to weld a pipe on,, i have some green and a lot of lint

i was able to refurb this muffler so i am good to go

 

[PA Plumber]

I think I have a big ole Stihl 070 / 090 muffler. Looks to be in fairly good shape.

 

[little possum]

Looking for a 350 Husky clutch or the likes. Whatever will work.

 

[mauserman028]

John Deere 55 SV ehco

i have a nice john deere 55sv 20 inch bar runs strong i like to trade to bigger homelite or or bigger saw has nice 3/8 chain with a hard nose bar starts and runs good
http://img580.imageshack.us/img580/7074/s6300808.jpg
http://img193.imageshack.us/img193/2622/s6300809m.jpg
http://img835.imageshack.us/img835/1275/s6300810.jpg
http://img849.imageshack.us/img849/9677/s6300812l.jpg

 

[Duke Thieroff]

Looking for the following parts for a Husqvarna 3120

Crank Bearings 503 25 00-02 x2
Crankcase Gasket Set
Crank Seals 503 26 02-05
Wrist Pin Bearing 503 13 29-01



Chris

 

[mauserman028]

900 evl parts

i like to find a extra falling spike. coil few other things let me know what u got pm me or email [email protected] :smile2:

 

[Mastermind]

I've got a Stihl 009L here that's missing a few of the rod bearing needles. I need three of the little suckers. I also could use a piston if anyone has a usable one. It's the same as an 011 and the Greek is about the only source. Thanks for any and all help on this. I've got some stuff to trade and green paper that is damn near worthless these days.

 

[sefh3]

Randy, I have those needle bearings that you're missing. What is the bore on the 009? I might have a piston too

 

[Mastermind]

Randy, I have those needle bearings that you're missing. What is the bore on the 009? I might have a piston too

It's 38mm Scott.

I sure appreciate you checking my friend. The piston for this saw is more expensive than one for an 066.

 

[sefh3]

I'm looking for the cover for the recoil for a TS760 cutoff saw. Here is a picture of the saw. I have parts to swap for it.

 

[Opihi59]

Connecting Rod needle bearings

I'm looking for a set, or maybe just a few needles for the connecting rod-crank journal connection on a Roper built Craftsman 3.7 917.353750 Saw. There are a number of other Roper 3.7 that have the same needles such as the XXX770, etc. Here's a few photos showing the needles and where they go. Anybody have some? Send me a PM.

What do I have to trade? Umm, loose change, eternal gratitude, a few beers, whatever you seem to think is reasonable from my Paypal account. In short, I may be a black hole of need, but a set of needle bearings would sure be nice. I have tried to search up what may be an equivalent but have come up way way short on this and have missed out on a few good deals on ebay for carcasses, etc but shipping costs out here have made parts saws cost-prohibitive.

I even looked here, but this particular Cow didn't have any either.

 

[Warped5]

I even looked here, but this particular Cow didn't have any either.

Ohhhhhhh ..... I wasn't quite prepared for that ..... :msp_scared: