Swap meet...

[Mastermind]

I'm looking for a wrap handle, chain brake, clutch cover and all the chain brake accessories for a Stihl 046. I have parts to trade.

Pretty sure I've got all the internal brake parts.

 

[sefh3]

Pretty sure I've got all the internal brake parts.

Do you have my addy? If not I can email or PM you.

 

[Modifiedmark]

Yep, it is the Roper, an early Roper with the D082 mount, not the later models with the D176 mount.. On the D176 bars, the oil hole is into the channel and on the D082, it is thru the bar. Yes, I can drill thru the bar, but the D176 bar takes a 72 link chain, and I just bought two new 74 link chains for the D082 bar.

Why would I do that? Well I bought the bar at the same time from a different source who a week later told me duh, we don't have/can't get it. Stuck since I can't return the chains. I may end up going the D176 route, but dang it all, I'd really like to get the right bar...........

Thanks.

I doubt you find a bar that takes 74 drive links . A oregon k 041 mount probably be your best bet as it fits your bar studs and oils through your adjuster holes.

Just get your chains cut to 70 DL.

 

[Mastermind]

Do you have my addy? If not I can email or PM you.

Send me a PMmmmmmmmmm :msp_biggrin:

 

[R2D]

Very big long shot......Stihl 090 137cc 66mm piston.

 

[Eccentric]

I doubt you find a bar that takes 74 drive links . A oregon k 041 mount probably be your best bet as it fits your bar studs and oils through your adjuster holes.

Just get your chains cut to 70 DL.

We've talked a bit more about his saw/bar/chain issue in PM's. I completely forgot about the K041 mount bars. He needs to run .325 pitch chain as that's the spur he has. That's why his DL count is higher than what'd be on a 20" bar with. 375.

 

[wigglesworth]

I'm in need of a nice top cover and air filter cover for a bubble top 066/660. I have cash or lots of parts to trade.

 

[sachsmo]

Very big long shot......Stihl 090 137cc 66mm piston.

Baileys has them with jug for $99.95, aftermarket of course. I wish they would make one for the 1100/2100 saws.

 

[MS460WOODCHUCK]

I am looking for a clutch cover to a poulan 3400. I'm in a bad need for this, the one on my saw got shattered today. I have cash to trade. PM me if you can help me out.

 

[R2D]

Baileys has them with jug for $99.95, aftermarket of course. I wish they would make one for the 1100/2100 saws.

Yes, I have seen the aftermarket stuff. For this beauty, I am hoping (very big long shot) to get good used OEM piston. I even sent out the original cylinder to get relined with NiSi at a race shop.

 

[Modifiedmark]

We've talked a bit more about his saw/bar/chain issue in PM's. I completely forgot about the K041 mount bars. He needs to run .325 pitch chain as that's the spur he has. That's why his DL count is higher than what'd be on a 20" bar with. 375.

Even more reason to use the K041 mount, there easy to find in .325 pitch. The The D176 are dang near impossable to find in that pitch.

The 74 drive link chains still wont work though, a 18" will want 72 and a 20" will want 78.

 

[Modifiedmark]

I am looking for a clutch cover to a poulan 3400. I'm in a bad need for this, the one on my saw got shattered today. I have cash to trade. PM me if you can help me out.

John, I think I might have a red plastic one....

 

[Modifiedmark]

28" .058 bars

I got 2 28" .058 3/8's bars I don't need. Both are Windsor speed tips.

One brand new in big Husky mount.

The other is a good used Partner (will work on Husky) mount bar. The rails are excellent and have been dressed but the tip has just a little wear on it.

What you got to trade?

I would be interested in 24" to 28".050 bars in Large Husky or Poulan/Echo D176 mounts or what ever.

 

[Modifiedmark]

Dolmar sprocket

I also have a NOS obsolete Oregon 27193X rim and drum setup for a Dolmar 153, 166. Its listing also says it fits a 152. It wont fit mine but might fit a late 152. It uses a 18mm bore on it.

 

[parrisw]

I'm looking for some 371/372 stuff. Need a chainbrake lever and handle, need the rubber carb mount, the part that the filter adapter clips to. Also need a couple handle bars, one full wrap if possible and one half wrap.

 

[wigglesworth]

I'm in need of a nice top cover and air filter cover for a bubble top 066/660. I have cash or lots of parts to trade.

Bump for this. If I cant find it shortly, im gonna be forced to buy new.

Got $$ and lots of parts to trade.

 

[Tree Wacker]

I am looking for a clutch cover to a poulan 3400. I'm in a bad need for this, the one on my saw got shattered today. I have cash to trade. PM me if you can help me out.

i might have one i'll have to look and see what i got.will one from a poulan 3800 work?

 

[MS460WOODCHUCK]

i might have one i'll have to look and see what i got.will one from a poulan 3800 work?

I'm pretty sure it will. Let me know what ya find.

 

[Tree Wacker]

I'm pretty sure it will. Let me know what ya find.

Pm sent found one

 

[timberdollars]

Poulan 3800 micro's

Just thought I'd throw this out there, Im turning loose of my Poulans, I can't afford my chainsaw addiction anymore. I need to stick with my Partners only. Too many saws not enough parts and $

So this 3800 is up for grabs prior to feebay its in the Poulan Thread from the other day.
Also this Micro s25cva, looks ok but needs carb kit (hardened up) and shows some scoring, missing some oem screws, good spark
A Micro 2300cva "Firewood" newer model black top, runs great, shows scoring, listed on eBay but?

swap Partners, Poulan Pro/Partner based saws, pp325, p100, p85, 5000+, green paper material.

May just list in the classifieds/feebay Monday