Swap meet...
- Thread starter Four Paws
- Start date
Help Support Arborist Forum:
gilraine
ArboristSite Guru
i have a complete poulan 361 with no spark and am looking for a flywheel for an 036.
sefh3
Addicted to ArboristSite
Still looking for one. I need these for non intelcarb.
Has anybody done that ?
I made an attempt sometime back and found something different on the case on the old version that made it look more complicated then expected so I skipped it.
Jwalker1911
Addicted to ArboristSite
looking for a 24" .063ga 3/8ths pitch stihl bar,36" 3/8s .063 ga stihl.....have a 30" stihl bar and a complete 026 to trade
Bump.
Also, all the fasteners/screws that hold on the coil, recoil cover and the top lid.
(only the big chunks were in the cardboard box it came in.)
Yeah the early 028 crankcase was different, and that's why the old brake system wouldn't fit the newer case. They redesigned the case and brake system
and the newer brake system has fewer parts. The old-school brake parts have been NLA from Stihl for years and years.
The brake kit for the early 028's are rare as hens teeth.....It has to be the "non crossing" type brake band......They're out there, but not common!
parrisw
Tree Freak
Do you know the part numbers? I could check my parts stock.
mp5n
ArboristSite Operative
Looking for a Shindaiwa 360 saw
I'm trying to track down a Shindaiwa 360 saw with a blown up motor. I picked one up which is missing a lot of parts. but with a good motor. If anyone can help out please PM.
Thanks,
MP5N
I'm trying to track down a Shindaiwa 360 saw with a blown up motor. I picked one up which is missing a lot of parts. but with a good motor. If anyone can help out please PM.
Thanks,
MP5N
Wanted
Husky 257 cylinder (got new piston already)
Stihl 029,290, 029 super, 310, 039, 390 muffler (with hardware preferably)
79cc dolmar p&c
PM me if you have any of the above.
Got stihl clam shell stuff... 024 crank case (i think 024...), different bars and chains... misc... or cash.
Husky 257 cylinder (got new piston already)
Stihl 029,290, 029 super, 310, 039, 390 muffler (with hardware preferably)
79cc dolmar p&c
PM me if you have any of the above.
Got stihl clam shell stuff... 024 crank case (i think 024...), different bars and chains... misc... or cash.
Last edited:
AU_K2500
NSM
anybody got a husky fuel line....Part number: 501 42 65-01
If not ill just use tygon and some RTV around the hole.
If not ill just use tygon and some RTV around the hole.
RTV won't hold for nothing.Gas will eat it.You really need the right fuel line.
If anything, there are gas/oil seal products. But RTV is a big no-no. For applications where it comes in contact with coolant, it's acceptable, but gas will eat it up very quickly.
AU_K2500
NSM
thanks for the tip fellas. I would like to have the right part too. randy duncan has it on fleebay. 19.00 plus shipping seems high, but it is a fairly rare part. Might just do it to have the right part.
This MAY OR MAY NOT WORK, but would a fuel line from a Mac 10-10 be acceptable? It seals in the same way you're describing. They still make them and they are plentiful, if your local saw shop doesn't have one, they can order it and you could have it for $10 or under, unless they're gougers.
ndlawrence
ArboristSite Guru
Looking for a good smaller/medium sized saw to pratice porting on. Pm me
