Swap meet...

[mdavlee]

hmm...


is this the 3/8" that's supposed to have the .404" kerf??

The LGX, LJX, and LPX are the same width kerf as the CL, CK, and CJ. The CLX, CJX, and CKX are wider kerf .404" sized cutters on 3/8" chassis. Here's a picture of the CKX and CK side by side.

 

[atvguns]

Looking for a 024 muffler

 

[AU_K2500]

looking for a 16" husky small mount bar. any usable condition. Used is preferred.

 

[Chris J.]

looking for a 16" husky small mount bar. any usable condition. Used is preferred.

Do you know if any of the below-listed Craftsman (relabelled Oregon) bars would work?

What I have (the formatting might be screwy because of the cut & paste):

NOS Craftsman Chainsaw Bars

Quantity........Length.........Craftsman #........Info on the Bar

2..................14” .............7136594.............71-36594 AL 14 91...E-Z Adjust...PAT 6061915

9..................16” .............7136626.............71-36626 S56...OREGON DX

10.................18”.............71336638...........71-36638...S62 OREGON DY

3...................20”.............71336599...........71-36599... CJ...E-Z Adjust...20....325... PAT 6061915

 

[AU_K2500]

no clue on that one....it might work! Im sure someone will come along and tell us....maybe

 

[cambl]

Jonsered 625/630/670 chain brake

Anyone have a chain brake ass'y for a Jony 625/630/670 ?

I have a full wrap handlebar to trade, maybe some other 670 misc parts.

Thanks.

 

[atvguns]

Looking for #25 #29 #30

 

[Work Saw Collector]

Looking for #25 #29 #30

Hope you get this found before the october GTG.

 

[8433jeff]

Do you know if any of the below-listed Craftsman (relabelled Oregon) bars would work?

What I have (the formatting might be screwy because of the cut & paste):

NOS Craftsman Chainsaw Bars

Quantity........Length.........Craftsman #........Info on the Bar

2..................14” .............7136594.............71-36594 AL 14 91...E-Z Adjust...PAT 6061915

9..................16” .............7136626.............71-36626 S56...OREGON DX

10.................18”.............71336638...........71-36638...S62 OREGON DY

3...................20”.............71336599...........71-36599... CJ...E-Z Adjust...20....325... PAT 6061915

16", S56 seems like a 3/8 LP or picco count, should be 66-67 DL for a .325. The bottom bars could be .325.

 

[AdamL]

Dolmar 7900

Looking to sell a dolmar Ps 7900 32 inch bar runs great 170 lb compression listed in classifieds as well... Email [email protected] for more info Asking $650 will ship to lower 48 united states for actuall shipping charges

Adam
View attachment 234519
View attachment 234520

 

[logging22]

Looking for #25 #29 #30

Im on it brother. Got a lead i think.

 

[diggers_dad]

Do you know if any of the below-listed Craftsman (relabelled Oregon) bars would work?

What I have (the formatting might be screwy because of the cut & paste):

NOS Craftsman Chainsaw Bars

Quantity........Length.........Craftsman #........Info on the Bar

2..................14” .............7136594.............71-36594 AL 14 91...E-Z Adjust...PAT 6061915

9..................16” .............7136626.............71-36626 S56...OREGON DX

10.................18”.............71336638...........71-36638...S62 OREGON DY

3...................20”.............71336599...........71-36599... CJ...E-Z Adjust...20....325... PAT 6061915

I'm pretty sure the small mount Husky is different than the Poulan / Craftsman mount. I think Husky puts their bar adjustment holes closer to the bar stud slot.

The 16" bars you show are for 3/8 lo-pro, 56 dl, .050; the 18" bars are the same except 62 dl.

 

[michale34]

dolmar 120

I got a dolmar 120 that will run but its been sitting in a barn for years I cleaned it up and put fresh gas and it started but was hard to restart i figured trash and gunked up carb from sitting i changed the gas line because it was mush so i guess the diaphrams are stiff . 75.00 shipped

 

[tmessenger]

I'm pretty sure the small mount Husky is different than the Poulan / Craftsman mount. I think Husky puts their bar adjustment holes closer to the bar stud slot.

The 16" bars you show are for 3/8 lo-pro, 56 dl, .050; the 18" bars are the same except 62 dl.

You can just file the adjustment hole a little bit, they work fine.

 

[tbone75]

I got a dolmar 120 that will run but its been sitting in a barn for years I cleaned it up and put fresh gas and it started but was hard to restart i figured trash and gunked up carb from sitting i changed the gas line because it was mush so i guess the diaphrams are stiff . 75.00 shipped

PM sent

 

[Warped5]

PM sent

.. hmmmm, John has gotten that Dolmar baaaaaaaaaaaaaaaaaaad!!

 

[tbone75]

.. hmmmm, John has gotten that Dolmar baaaaaaaaaaaaaaaaaaad!!

You right! I have several now! LOL Just can't help myself I like them Dolmars! :hmm3grin2orange: OK let me see? 111,112 Silver,115,116si,120,120si,133,143 so far. LOL Guess I could include the Makita 6401/7900

 

[michale34]

PM sent

saw sold thanks everyone

 

[diggers_dad]

PM sent

You are a turd.

 

[sefh3]

You are a turd.

Sure was fast for a slug :hmm3grin2orange: