Swap meet...

[briantutt]

HMMMM let me look i might some laying around that came off of a little homelite. is that one you have a 8mm with flat head screw driver slot?

IPL says "Pan head self-tapping screw IS-P6x19" they measure .225 inches across peak of the outer thread.

 

[little possum]

Anybody happen to have a 10-12" bar for a 020AV super? And maybe the A/V mount that goes from the handle to the case..

 

[dh1984]

IPL says "Pan head self-tapping screw IS-P6x19" they measure .225 inches across peak of the outer thread.

Will these work?

 

[wigglesworth]

Still looking for a 066 muffler body. I don't need a cover.

Lookie what muh boy found brad.

 

[briantutt]

Will these work?

Maybe! if the pitch is the same they should cut threads. What do they measure across thread peeks ?

Brian

 

[plumbcrazyjr]

i find myself in need of a gas tank for a ms280 lots of parts and a little green paper to trade
thanks

 

[Scooterbum]

Maybe! if the pitch is the same they should cut threads. What do they measure across thread peeks ?

Brian

Your gonna need the depth and width of the landings between the peaks also.



















































































Wow...............what was it PT Barnum said?

 

[Saw Dr.]

Maybe! if the pitch is the same they should cut threads. What do they measure across thread peeks ?

Brian

I wouldn't do it. Use what is supposed to be in there. If they strip it is a major pain in the _____. There are a few ways to repair it, but probably better to use the OEM screws. The headache to repair it will not be worth the $2 you save on screws.

 

[briantutt]

I wouldn't do it. Use what is supposed to be in there. If they strip it is a major pain in the _____. There are a few ways to repair it, but probably better to use the OEM screws. The headache to repair it will not be worth the $2 you save on screws.

I agree. Good point.

Brian

 

[PogoInTheWoods]

Wow...............what was it PT Barnum said?

Take my wife, please?

 

[PB]

This is a long shot, but does anyone have an oiler pump gear for a Husqvarna 316? It's an electric saw. I picked up the Jonsered version today and the gear is stripped out.

 

[PogoInTheWoods]

Speakin' of suckers, I seem to have been led to believe there are different carbs for a points 032 and an electronic 032. I'm seeing both a HU-51C and a WA-49B without any specific designation one way or another in my IPL.

I'm gonna take a SWAG that either one will work in either ignition setup? If so, anyone have one to spare? Or maybe a 032 parts saw?

It's a favor for a buddy. Has parts. Has caish.

TIA.

Poge

 

[tomdcoker]

Speakin' of suckers, I seem to have been led to believe there are different carbs for a points 032 and an electronic 032. I'm seeing both a HU-51C and a WA-49B without any specific designation one way or another in my IPL.

I'm gonna take a SWAG that either one will work in either ignition setup? If so, anyone have one to spare? Or maybe a 032 parts saw?

It's a favor for a buddy. Has parts. Has caish.

TIA.

Poge

I have one. It is a HU51A. It was removed from an 032. PM me you address and it is yours. Tom

 

[blackoak]

Anybody have two of these self tapping screws to hold the handle on my stihl 028 WB ?



Brian

I have 100 or so. PM me you address and I'll send you a few. These are actual Stihl T-27 torxs head screws that came out of parts saws I have parted out over the years.

 

[briantutt]

I have 100 or so. PM me you address and I'll send you a few. These are actual Stihl T-27 torxs head screws that came out of parts saws I have parted out over the years.

Wow great. I will pm you! thanks.

Brian

 

[PogoInTheWoods]

I have one. It is a HU51A. It was removed from an 032. PM me you address and it is yours. Tom

Thanks, Tom. PM sent.

Poge

 

[tmessenger]

Looking for Walbro WT-195

Looking for a WT-195 carb for a Stihl 026

Stuff to trade:

Have a Sthil 039 that ate a wrist pin clip so have about everything other then the piston/cylinder from this saw.

Jonsered 920 cylinder and flywheel

Dolmar 144 recoil / starter and top cover.

stihl 028 Super Woodboss top cover and recoil / starter.

stihl 009 , 011, 180 parts,

Homelite EZ p/c 38mm (nice, 175 psi compression)loads of other EZ and Super EZ parts, some super 2 parts, XL12 recoil / starter, Homelite 360 clutch cover.

Stihl 040 muffler.

NOS Pioneer P28 clutch covers one has a chain brake.

Mac SP 40 most parts + B/C

 

[SawGarage]

Bump

I could send ya a PM, JJ.... but linkage, clutch/drum, etc, and piston should cover it..


up for trade...


I have a few NEW 33RSC chains:

.050 Ga 60DL & 66DL

as well as 3003 mount Bars a few new, some lightly used 16, 18, 20.

357/9 starter

044 plastics, muffler, 10mm top end with machine marks still, other crankcase parts, etc

3800 Poulan parts

288 parts

394/5 parts


I could use:

late 066/660 plastics, filter, muffler

044/046 muffler cover
metal Stihl Clutch cover

272 brake cover
288 brake cover, muffer, carb & intake stuff
starter

good, or rebuildable 394/5 case

5100/5 project

 

[fastLeo151]

I still an looking for a 066 flat top cylinder, I am also looking for a large sprocket cover for the same saw

I am needing cylinder studs for a 041 super

Thanks

 

[Jacob J.]

Looking for a WT-195 carb for a Stihl 026

Tim- I think I have an extra. I'll do some digging tomorrow.