Swap meet...

[hrhunter]

Thanks cowroy for helping me out. I also need a throttle rod for the 026 and a gas tank vent. The previous owner had a piece of rag stuck in the hole.

 

[sefh3]

Thanks cowroy for helping me out. I also need a throttle rod for the 026 and a gas tank vent. The previous owner had a piece of rag stuck in the hole.

Post a picture of your saw. They made about a dozen different types of vents for the 026's. Also need a picture of the air filter install looking at the tank vent.

 

[o8f150]

i know i will have better luck peeing to the top of a 20 foot rope but does anyone have a fuel line for a solo 603, i need it to fix dhibbs75s saw for him,, i have some items to trade and some useless green backs

 

[GrizzlyAdams86]

Still looking for a engine/top cover for a Echo 900EVL. Have greenbacks for trade.

Bump.

 

[Brushwacker]

Anyone out there have a carb for a McCulloch 3200 series saw? I am trying to get my friends saw to run and it either floods or won't draw fuel. It will run with a prime of the carb but that is it. The gaskets and needle are new and I am at a loss with this one. No idea where to go next besides a new carb. It is a Zama C1Q if that is helpful. Send me a PM if you have one you would be willing to part with. Low on trading parts but have cash.

I have a NOS Zama, says C1 on top, also has 8 near the idle screw head. McCulloch P/N 094496.
I don't see Q if thats necessary.

Also have a couple Zama M7 07A P/N 214082B or 90918-01 which I think is a kit #.

 

[hrhunter]

Sent from my VS920 4G using Tapatalk 2

Here are some pictures of the gas tank vent area. I need the pieces for the vent. sefh3 requested some pictures to better identify which one I needed. Hope this helps.

 

[shawn022]

In need of a piston and cylinder for a ms460, or just the cylinder. Also need a half wrap for the 460.

I need a half wrap for a 440. And everything from the carb studs out, not including the a/f cover. 044 stuff will work.

Pm me with needs/wants.

 

[Jacob J.]

i know i will have better luck peeing to the top of a 20 foot rope but does anyone have a fuel line for a solo 603, i need it to fix dhibbs75s saw for him,, i have some items to trade and some useless green backs

Those are still available from Solo USA.

Bump.

Parts for an Echo 900 are pretty rare. Your best bet is to call Bryce.

In need of a piston and cylinder for a ms460, or just the cylinder. Also need a half wrap for the 460.

I need a half wrap for a 440. And everything from the carb studs out, not including the a/f cover. 044 stuff will work.

Pm me with needs/wants.

What do you have to trade for this stuff?

 

[shawn022]

What do you have to trade for this stuff?[/QUOTE]


Got some 064/066 /084 top covers 066 flywheels(metal and poly) 064? coil, 066,660 recoil covers(need paint) usable 066 muffler, 066 clutch, AM 066 piston, AM P/C (Star Grey?)for a 076, 076,051 odds and ends, 028 odds and ends, 026 clutch, brake handle and? 440,066,064 muffler covers

Nos pistons. 08s, 07s, 028s

Also have used carb diaphrams and $$

 

[DSS]

I need...

Coil and all associated wires/mounting bolts for a CS-56 Deere.

Coil for a 488 shindaiwa

Top cover for a 3400 poulan. I'd take a good used air filter too.

Randy, did you get a dolmar jug yet? The one I have is a 401 makita, which I think is the same thing?

Trade junk/green paper/pie/jam etc...

 

[PB]

I have a NOS Zama, says C1 on top, also has 8 near the idle screw head. McCulloch P/N 094496.
I don't see Q if thats necessary.

Also have a couple Zama M7 07A P/N 214082B or 90918-01 which I think is a kit #.

Would you happen to have picture? I will go look again at this carb on the saw.

 

[Steve NW WI]

I have a set of rings here, got em off the bay as 47MM, they are actually 52mm, 1.5mm thick. Ideally looking for a 47 x 1.5 set (for a 264 Olympik), or make me an offer.

Bump...Anyone need these things? Or have the rings I need?

 

[Mastermind]

I need...

Coil and all associated wires/mounting bolts for a CS-56 Deere.

Coil for a 488 shindaiwa

Top cover for a 3400 poulan. I'd take a good used air filter too.

Randy, did you get a dolmar jug yet? The one I have is a 401 makita, which I think is the same thing?

Trade junk/green paper/pie/jam etc...

No not yet Chris.....and yep the 401 makita is the same. :msp_wink:

 

[battlefordguy]

Walbro #194 - Stihl 026

Hello

Looking for a walbro #194 carb, for stihl 026.
Can canabolize a HM XL-12 , or canuck bucks for trade.

 

[DSS]

I need...

Coil and all associated wires/mounting bolts for a CS-56 Deere.

Coil for a 488 shindaiwa

Top cover for a 3400 poulan. I'd take a good used air filter too.

Randy, did you get a dolmar jug yet? The one I have is a 401 makita, which I think is the same thing?

Trade junk/green paper/pie/jam etc...

No not yet Chris.....and yep the 401 makita is the same. :msp_wink:

OK, Your jug will be in the mail shortly.

I got the 3400 stuff, I still need the two coils.

 

[Eccentric]

I need...

Coil and all associated wires/mounting bolts for a CS-56 Deere.

Coil for a 488 shindaiwa

Top cover for a 3400 poulan. I'd take a good used air filter too.

Randy, did you get a dolmar jug yet? The one I have is a 401 makita, which I think is the same thing?

Trade junk/green paper/pie/jam etc...

Chris those air filters are available for around $5-$7 (USD) new from Oregon and Stens.

 

[DSS]

Chris those air filters are available for around $5-$7 (USD) new from Oregon and Stens.

Yeah, I been waiting till I needed a bunch of stuff so the shipping didn't kill me Aaron. Got a good one anyway

 

[Eccentric]

Yeah, I been waiting till I needed a bunch of stuff so the shipping didn't kill me Aaron. Got a good one anyway

I hear that. Sucks to pay $10 shipping for a $5 part....

 

[plumbcrazyjr]

I need solo 667 and 651 parts pieces or whole saws pm me with what you got and what you need for it
thanks
eric

 

[cnice_37]

Bump...Anyone need these things? Or have the rings I need?

Oh man Steve - I needed those yesterday! Just bought them off the 'bay last night. Can't help you with the 47mm stuff either.