the all aussie dribble thread!

[peter92]

Benny can you please stop making out that you know what you're talking about? Anybody would think you're a bloody Stihl dealer or sumfin...

Ok Matt, whats the best set up for cutting say 6'' longs
regards peter

 

[MCW]

Ok Matt, whats the best set up for cutting say 6'' longs
regards peter

Husky 3120 with 6' bar

Nah Benny is spot on. He knows what he's talking about. If it is clean stuff consider 3/8"LP as that cuts pretty quick but if it's a bit dirty go .325" semi chisel.

 

[peter92]

Thanks Matt
Its a bastard to start , about 15 pulls but once it starts its fine
I just realised i rebuilt it 4yrs ago apart from the carby
Hasnt been started for that long
Where do i start
Regards Peter

 

[bennn*e]

Sounds like a lazy pump diaphragm. I'd chuck a carby kit at it and check the impulse hose too. Best place to start

 

[MCW]

Sounds like a lazy pump diaphragm. I'd chuck a carby kit at it and check the impulse hose too. Best place to start

I was going to say exactly the same thing (after calling you for advice!).

 

[peter92]

Thanks Guys
I will check out the hose and retune to about 1 turn out each and fined out what a kit will cost ithink its a W carby but not sure til i check it out
Would it be wise to run it detuned for awhile
Regards Peter

 

[MCW]

Thanks Guys
I will check out the hose and retune to about 1 turn out each and fined out what a kit will cost ithink its a W carby but not sure til i check it out
Would it be wise to run it detuned for awhile
Regards Peter

No need to run it detuned. Just run it like you stole it

 

[ausneil 1]

I was going to say exactly the same thing (after calling you for advice!).[/QUOTE]

hahahahaha, that's good.

 

[tdi-rick]

View attachment 312908

Bwahaha, I'll have to pinch that Wayne and send to mum!

 

[460cixy]

Forgive me farther for I have sinned

 

[ozflea]

Forgive me farther for I have sinned

Welcome to the smart dark side ................ another super smart man

 

[460cixy]

Dident take you long lucky it's not mine. Have cleaned it up and it runs on start ya bastard. But won't run with out it. So carbs comeing apart after lunch

 

[gmax]

Forgive me farther for I have sinned

Looks like a 250? for your sake I hope that's a tilly carb

 

[ausneil 1]

Forgive me farther for I have sinned

Won't be much wrong with the yellow boat anchor Matty 2 if it starts then stops. looks complete too.
Do you have some magnets in your kit bag ???

 

[460cixy]

Looks like a 250? for your sake I hope that's a tilly carb

380a and yes it was a tillitson not a zamma or some other od bod bit of junk

 

[460cixy]

IMG 0279 - YouTube its alive. Just . And Neil I shouldn't need a magnet all nuts and bolts were replaced with nylok nuts backed up by loctite bearing retainer. They should stay tight for at Least tank of fuel

 

[ausneil 1]

IMG 0279 - YouTube its alive. Just . And Neil I shouldn't need a magnet all nuts and bolts were replaced with nylok nuts backed up by loctite bearing retainer. They should stay tight for at Least tank of fuel

Good for you Matty 2, and to think you done all this without specialist mac help.
bravo

 

[derwoodii]

Forgive me farther for I have sinned

Luke 23:34:

I see yer gotz a can of start yer bastard ether close at hand handy dandy stuff that eh

 

[derwoodii]

aaw knaakered dear daughter no1 had to go hospital last nite all the symptom of meningitis 2 days of massive pain killer resistant headaches photophobic sore neck etc etc they ran the test did all to ensure good as & very happy about that but was 3 am turn in for daddy

Ha n she was suppose to be doing a nursing exam on pain management today

 

[460cixy]

Mate I hope she gets well soon mate I've spent more time in hospital then I care to remember