The made in north america Old Magnesium Swap Meet.

[dce1843]

Hey guys. Looking for handlebars, fuel cap and mounts for a Double Eagle 80. Also would like to find clutch cover with chain brake guts and handle for a PP 655. Thanks

 

[pioneerguy600]

Would the whole recoil off a Eager Beaver 2014 work or just the spring? I can't find an IPL for a "Titan 200 Junior".

Carl, the Titan 200 Junior was made back in 1948-50 I think, I have a couple of them,

 

[67L36Driver]

Carl, the Titan 200 Junior was made back in 1948-50 I think, I have a couple of them,

Man, was I lookin' for the wrong Titan! The name made me think of one of the late Macs. Titan 35, 40, Titan 50 or 57.

 

[pioneerguy600]

Man, was I lookin' for the wrong Titan! The name made me think of one of the late Macs. Titan 35, 40, Titan 50 or 57.

Yep,..there`s a big difference between them makes.

 

[RandyMac]

Any idea what these came off of?

 

[Mr. Bow Saw]

Any idea what these came off of?

The rusty bar would be for a saw something like this Lamb bar.

The other bar looks like it fits a few different old saws.


Yours has a oval hole and this one is round hole.

 

[polkat]

Yep,..there`s a big difference between them makes.

would there be any other model that has the same recoil spring or assembly, the saw is too nice to shove in the back corner.

 

[Eccentric]

Dream on!!

I been watching for one of these going on years now. Bill G has a couple, Wayne Sutton in Oregon has 4 in the museum.. I saw them.

Hey now. I said it was a longshot....:msp_unsure:

I've been looking for an XL-15/XL-Automatic Gear Drive saw for years too. Found one............but it's missing all of the XL-15 specific parts except the MN/SN tag and the unique color combo and badging. For now it's basically an early XL-12, but red/white instead of blue/white...

Hell, the gearcase that was taken off of my XL-15 has to be somewhere. I doubt it was removed to put on another saw, as mine's in great shape both inside and out. It's probably in a junk box in somebody's garage in Oregon. The fellow that I got the saw from has more important things than chainsaws going on in his life right now. When things settle down for him I'll ask him where he got the saw. Maybe I can track that gearbox down. Now that would be a longshot...

 

[67L36Driver]

Lombard parts.

Who needed the 68c Lombard piston? I also have serviceable rings.


I lost trac of what thread we were in when it was mentioned.

 

[jerrycmorrow]

need a fuel cap for my poulan 306A. played swap-a-part and discovered that the cap off my 361 fits very nicely as does the cap off my homie C-5 (non-vented but correct size). the cap off my monkey ward saw fits too but its not vented either. looks like there may be several makes that will fit.
also needing a vented cap for my C-5.
this appears to be the "fuel cap phase" for me. not sure what else will fit but i'm not proud, just want functional caps. anyone got fuel caps they'd be willing to part with?
also posted on poulan thread and homelite thread
thanks, jerry

 

[Mastermind]

I have quite a bit of Homelite 650 parts to trade....

 

[Jacob J.]

I have quite a bit of Homelite 650 parts to trade....

Do you have an airbox/pistol grip? Where the mounts screw into the airbox on my 750 is all stripped out.

 

[Eccentric]

Do you have an airbox/pistol grip? Where the mounts screw into the airbox on my 750 is all stripped out.

Jacob I have one, but there's a small crack on the rear handle portion (near the decomp/throttle lock lever slot). Dunno if it could be welded. There's also the steel threaded ring from one of the old AV buffers stuck in the socket where it threads in. It can probably be unscrewed (been soaking it with PB Blaster). Never bothered to try to unscrew it, as I replaced the carb box/handle with a good used one from a friend here. My handle is also a bare casting (except for an oil line fitting or two) as I already stripped it to send the trigger/throttle lock/decomp parts to Fraser. This gem is yours if you want it...

 

[Eccentric]

McCulloch Super 2-10A Needle Extensions and hardware

I just got a McCulloch Super 2-10A (wife has claimed it.........but that's another story). It has an SDC carb (thankfully) and is the type with the short adjustment needles that are turned by long spring loaded 'screw extensions' that pass through the carb box. Both extensions and the springs and retaining rings are missing from the saw. I can of course still run the saw by adjusting the needles with the AF and cover off (and plugging the two holes in the carb box)...............but would really like to have the extensions on it. Anybody here have those two extensions plus the springs and retaining rings? I can furnish part numbers if needed. My saw has a 14 SN prefix and the model # is 600025.

Edit:

That part numbers for the extensions and related hardware are:

-68102 for the H needle extension.

-68101 for the L needle extension.

-67363 for each spring. I need two of 'em.

-110512 for each retaining ring. I need two.

Looks like I may also need a DSP valve pin (83166) as the 'head' on the end of the valve stem seems to have come loose. Pressing the button (which moves the linkage and pulls the valve and spring away from the cylinder) moves the spring and the 'head' of the valve. The valve pin itself seems to be staying put. Compression feels the same with the button pushed and not pushed...

I also need the 10-24-3/4" hex head screw (102289) and lock plate (68508) for the lower handle brace. Probably will just get a screw and lockwasher from the hardware store....

 

[bplust]

I just acquired a Homelite 700g that has plenty of compression and spark. What it doesn't have is a starter puller and pulley cover. Basically, I'm looking right at the spring, and the flywheel behind it.

I'm looking to either get the cover & pulley, or trade it and send this saw somewhere else. I have $$$ and parts to trade.

Additionally, regarding old Mag, I have:

1 Homelite 600d
2 Homelite Zip
1 Homelite Buz
1 Strunk (Not sure what it is exactly, but I'm pretty sure it's a David Bradley rebrand).

 

[RandyMac]

Any interest in B&Cs with heavy chain?

The chain for the bright bar is 9/16" chisel, I have a new McCulloch spur sprocket to go with it.

The other on is a Homelite, 1/2" chain.

I also have a length of 9/16" chipper, 67 DLs.

 

[Eccentric]

I'm interested in the 1/2" Homelite B/C for BrocLuno's Super Wiz 77. Hopefully I can talk him into it. Send me a PM with what you're looking to get out of that B/C..:cool2:

 

[Mastermind]

Do you have an airbox/pistol grip? Where the mounts screw into the airbox on my 750 is all stripped out.

Yes Sir. I have two of them. One is NOS and the other is used in great shape. I'll send you one.

I got those bushings today........Thanks a bunch. That saw is ready to build now.

 

[paccity]

Yes Sir. I have two of them. One is NOS and the other is used in great shape. I'll send you one.

I got those bushings today........Thanks a bunch. That saw is ready to build now.

randy. i completely spaced your banana handle. i'll get that out soon.

 

[promac850]

I would like a airbox/handle, lower handle brace, and air filter for a 1-43. Does not have to be perfect, just no white death... I got plans for that engine from the donor to the 790 project...

Will pay with cigars.

Also looking for an air filter cover for a Super 44A. Good to great condition preferred if possible.