The made in north america Old Magnesium Swap Meet.

[Wagnerwerks]

The 450 and 550 are sister saws, with many interchangeable parts. The DM54/540 is a completely different animal. I was merely trying to answer the question as to whether a DM50 would be a good parts rig for a DM54.

Thank you. . I'm just trying to get these straight.

 

[psuiewalsh]

The 450 and 550 are sister saws, with many interchangeable parts. The DM54/540 is a completely different animal. I was merely trying to answer the question as to whether a DM50 would be a good parts rig for a DM54.

Thanks for the input.

 

[djones]

I find myself in need of a Mac 700 P&c, rings would be nice too.

I also am looking for a piston and rings for a Mac 10-10.

I have a couple of boxes of Mac 10-10 parts, a 2150 Poulan that runs but needs a clutch cover, filter cover, bar and chain and a couple other parts, some stihl 020, 021, 029 and of course dead presidents.

 

[chainsawwhisperer]

I find myself in need of a Mac 700 P&c, rings would be nice too.

I also am looking for a piston and rings for a Mac 10-10.

I have a couple of boxes of Mac 10-10 parts, a 2150 Poulan that runs but needs a clutch cover, filter cover, bar and chain and a couple other parts, some stihl 020, 021, 029 and of course dead presidents.

I'm 99% sure I have a piston& rings...I'll have a look and let you know.
jim

 

[djones]

Thank you Jim, that would definitely be a big help,
Dave

 

[chainsawwhisperer]

Thank you Jim, that would definitely be a big help,
Dave

I do have one (piston,rings,rod), and it's nice. Looks like it came out of a low hour saw.
Pm me and we'll talk.
Jim

 

[Wagnerwerks]

Wright bars

My local shop has 2 Nos Wright hard nose bars. One is around a 20 and the other is maybe a 24-25. They have the orange lettering. He wants to sell them, but has no idea on value. Any offers? I told him I'd ask. They are the mount with a slot and four squares and are wider bars....

 

[67L36Driver]

My local shop has 2 Nos Wright hard nose bars. One is around a 20 and the other is maybe a 24-25. They have the orange lettering. He wants to sell them, but has no idea on value. Any offers? I told him I'd ask. They are the mount with a slot and four squares and are wider bars....

Kind of like this?

Post a pic and measure the guage for sure.

 

[Wagnerwerks]

Kind of like this?

Post a pic and measure the guage for sure.

Not quite... My ADD self was all giddy about the bars I wanted and didn't take a pic. I'll get a pic when I head over next, or find it online for you.

 

[dff110]

Pouland Parts

Looking for parts for a Pouland 3400 anti vib

need a good P&C and an ignition coil.

Have lots of remington parts, Craptsman saws, and green backs to trade.

 

[Modifiedmark]

I could use a Tillotson HL 276A carb if anyone has one laying around. Its from a direct drive sand cast Poulan. Dont know for sure if any others will interchange.

 

[Eccentric]

I could use a Tillotson HL 276A carb if anyone has one laying around. Its from a direct drive sand cast Poulan. Dont know for sure if any others will interchange.

Mark do you have any pictures of the correct carb for your saw showing the throttle shaft arms, idle speed screw placement, choke arm type, fuel inlet type, and needle placement? I'll bet an HL from a vertical cylinder Homelite (Buz, Zip, etc) would work fine. I could probably set you up with one.

 

[67L36Driver]

I have a Tilly HL 141 A off a Homie C5 laying around.

IIRC its very much like the one on my Poulan model 47 except they are mounted 'upside down'.

Also, that number (276) is ringing a bell. One of my Remy Bantam types uses it. My robbin's egg blue Wards/Remington.

 

[Modifiedmark]

Mark do you have any pictures of the correct carb for your saw showing the throttle shaft arms, idle speed screw placement, choke arm type, fuel inlet type, and needle placement? I'll bet an HL from a vertical cylinder Homelite (Buz, Zip, etc) would work fine. I could probably set you up with one.

I'll check tonight about a picture

I have a Tilly HL 141 A off a Homie C5 laying around.

IIRC its very much like the one on my Poulan model 47 except they are mounted 'upside down'.

Also, that number (276) is ringing a bell. One of my Remy Bantam types uses it. My robbin's egg blue Wards/Remington.

Might work Carl, I'm just not sure on these HL's. Have to check the venturi sizes. I would think, throttle and chokes could be swappped around if there same size carbs...

 

[djones]

Here are the photos TedView attachment 258273View attachment 258274View attachment 258275View attachment 258276

 

[little possum]

Fellas its time to clean up the shop. I got a couple ol mag saws... Mac D36 a 1-43 and 1-41 a early yellow top 250. Dayton (361 poulan) Homelite Super EZ and a parts rig I think. Those will be the first list. Cant remember right off hand what all is out there. Most of them were runners..

 

[sefh3]

I'm interested in your Super ez and parts rig for it. Hows the piston? Whatcha needing for it? PM me.

 

[little possum]

361

306

(Scott here are a few pics)

D-36
Fellas here are a couple pictures. Not tryin to get rich just got to get some space to move in the shop! Life is changin gears and saws gotta go!

 

[little possum]

1-43

1-41

250 I do have the wrap handle

Montgomery wards

Homelite 330&360 as well.

 

[hemiyota]

Poulan Model 31 parts needed

Does anyone have a top cover w/screws, and an air filter assembly? Just picked up a 31 with a very nice p/c, but the owner "misplaced" these parts..:bang: