The made in north america Old Magnesium Swap Meet.

[crane]

Get Sawdust21's attention. I sent him a mostly complete GL-7 a while back to use for parts.

Thanks. It's time I catch up with sawdust21 again. I see he has been painting some real beauties!!

 

[Warped5]

Might anyone have a 24" ... .063 ... .404 (if sprocket tip) bar to fit a Mac 250? I have stuff to trade .. please PM me ... thanks!

 

[Eccentric]

Might anyone have a 24" ... .063 ... .404 (if sprocket tip) bar to fit a Mac 250? I have stuff to trade .. please PM me ... thanks!

No sprocket noses.............but I probably have a 24" .063G hardnose or two that I could part with...

 

[Arrowhead]

Might anyone have a 24" ... .063 ... .404 (if sprocket tip) bar to fit a Mac 250? I have stuff to trade .. please PM me ... thanks!

Ted, I'll check the pile tomorrow. I don't have any Mac branded bars for it, if I have one it would be NOS Oregon, Tsmura, Total... etc.

 

[Warped5]

Ted, I'll check the pile tomorrow. I don't have any Mac branded bars for it, if I have one it would be NOS Oregon, Tsmura, Total... etc.

Thanks, neighbor!

 

[Arrowhead]

Ted

I sold my 250 months ago... I can't remember the bar pattern.
Anybody have a pattern they can email me? I cam PM my email addy to anyone that has a pattern.

 

[Warped5]

Ted

I sold my 250 months ago... I can't remember the bar pattern.
Anybody have a pattern they can email me? I cam PM my email addy to anyone that has a pattern.

Don't worry about it, Ed.

One will show up one of these days ... that saw just got pushed back in the queue ...

 

[Eccentric]

Ted

I sold my 250 months ago... I can't remember the bar pattern.
Anybody have a pattern they can email me? I cam PM my email addy to anyone that has a pattern.

Looks a lot like a large frame Homelite (C-Series, 1050, Zip, etc) bar. Often has a 'thumbnail' cut milled into the side for the OLD saws that had the 'big screw head' tensioners. Four holes (two for oil, and two tensioners) on the old ones. Later large frame Mac bars look like 'oversized' 10-series Mac bars. Only two oblong combination oiler/tensioner holes.

Old style 'four hole' bar and newer style 'two hole' bar.

Old style bar (that I modified to oil correctly with the newer bar plates), showing the 'thumbnail' adjuster cut. That cut is unused on most large frame saws (after the D-44).

Ed PM your email address to me if you need to.

 

[Arrowhead]

Ted, these are the only ones I have that came close. I think they are both Homelite mounts. Might be able to mod a little to fit the 250.
24" hardnose. I can send ya one if you like... I still owe ya. Or if you want to hold off for a direct fit or Mac branded... I understand.

 

[Warped5]

Ed, I'll be holding off for now. Thank you for checking, though.

 

[crane]

shop clean out........

Looking to unload these, need to finnish up some projects and make room.

trading:

Mac 10-10.............runs but needs fuel line. Has crack on clutch cover
Mac 1-41...............runs good, has all the paint and great model decal.
Mac D-30(lubimac oil system)....runs and is in great shape. See pics posted recently in the mac thread.
Mac 1-40................runs and is in great shape
IEL HC....................had engine running, but exterior rough. Parts saw
IEL Ra.....................good compression/no spark. Will look into if interested
Homelite XL-12.........looks good, have not tried to start
Homelite XL-102........in pieces, has had parts painted but never reassembled. Have full decal set(not installed)
Remington SL-5.........missing recoil. parts saw
Pioneer 1130..............Has broken recoil rope. don't know compression or spark. Will look into if interested
Pioneer 1200A.............saw has ran, but weak compression. Paint not great.
I Also have a set of NOS PL-4 rings, PL handlebars(some with rubber), PL air filter covers, SL-9 p/c(used) some remington starter cups and screens.
2x 070/090 airfilter covers NOS
some misc Mac 99 Two man saw parts
I also listed some newer stuff in the swap meet thread.

Looking for:

36"+ bar for stihl 070 Can be hardnose.
Remington Gear Drive project (770/660/754)....Just throwing it out there
Remington roller noses...2.5,3.5"
Remington bars 17,19,21" P/N's A1014,A1015,A1016
GL-7 parts
Mac 99 oiler cable, model plate
Mall 2MG air filter screw in plate......heck any Mall stuff
Feel free to offer up. Looking to trade for stuff I need or want. Pics on request

 

[rocketnorton]

Looking to unload these, need to finnish up some projects and make room.

trading:

Mac 10-10.............runs but needs fuel line. Has crack on clutch cover
Mac 1-41...............runs good, has all the paint and great model decal.
Mac D-30(lubimac oil system)....runs and is in great shape. See pics posted recently in the mac thread.
Mac 1-40................runs and is in great shape
IEL HC....................had engine running, but exterior rough. Parts saw
IEL Ra.....................good compression/no spark. Will look into if interested
Homelite XL-12.........looks good, have not tried to start
Homelite XL-102........in pieces, has had parts painted but never reassembled. Have full decal set(not installed)
Remington SL-5.........missing recoil. parts saw
Pioneer 1130..............Has broken recoil rope. don't know compression or spark. Will look into if interested
Pioneer 1200A.............saw has ran, but weak compression. Paint not great.
I Also have a set of NOS PL-4 rings, PL handlebars(some with rubber), PL air filter covers, SL-9 p/c(used) some remington starter cups and screens.
2x 070/090 airfilter covers NOS
some misc Mac 99 Two man saw parts
I also listed some newer stuff in the swap meet thread.

Looking for:

36"+ bar for stihl 070 Can be hardnose.
Remington Gear Drive project (770/660/754)....Just throwing it out there
Remington roller noses...2.5,3.5"
Remington bars 17,19,21" P/N's A1014,A1015,A1016
GL-7 parts
Mac 99 oiler cable, model plate
Mall 2MG air filter screw in plate......heck any Mall stuff
Feel free to offer up. Looking to trade for stuff I need or want. Pics on request

what u want 4 ra? got pics?

 

[crane]

PM sent

Not trying to sell, looking to trade........got anything on the list??? got anything interesting to trade????

If no trades come up after a while, I'll list the saws in the classifieds

 

[rocketnorton]

its all comin back, have nothing on yer wanted list... pm sent back... am interested in seein vid/pics... is yours '57or 58? mine is '57 I think cause low [4 digit] #... wheres nobleford? I was in ab for abt 10 yrs. claresholm one yr, edm/st. albert, the rest...

 

[djones]

OK I see that my post during the hackers party is lost so I'll repost now. I'm looking for a good coil for a PM610. It is an electronic ignition coil with a long spark plug lead. I'm trying to repair a neighbors saw and need the coil to get her running. I have Pro Mac 10-10 parts to trade plus some Stihl 021 and 029 parts plus some odd 017 & 020 parts. I also have a poulan 2150 parts saw that runs. It's missing some plastic and the clutch. Let me know what you need.

 

[Mo. Jim]

OK I see that my post during the hackers party is lost so I'll repost now. I'm looking for a good coil for a PM610. It is an electronic ignition coil with a long spark plug lead. I'm trying to repair a neighbors saw and need the coil to get her running. I have Pro Mac 10-10 parts to trade plus some Stihl 021 and 029 parts plus some odd 017 & 020 parts. I also have a poulan 2150 parts saw that runs. It's missing some plastic and the clutch. Let me know what you need.

PM sent

 

[watsonr]

Don't worry about it, Ed.

One will show up one of these days ... that saw just got pushed back in the queue ...

Ted,
I probably have a 24" .063 roller nose at the house to fit that saw and may even have two or three hard nosed ones with the correct bar adjuster slot. It came on a SP125 and was obviously way to short! When I get home next week, I'll look for it.

 

[Warped5]

Ted,
I probably have a 24" .063 roller nose at the house to fit that saw and may even have two or three hard nosed ones with the correct bar adjuster slot. It came on a SP125 and was obviously way to short! When I get home next week, I'll look for it.

No need now, Randy. Crisis has been avoided. But thanks!

 

[watsonr]

I was hoping to trade the bar to you for the 6' Homelite mount I need for the 2100 Super.....guess that's a "NO"?

 

[Warped5]

I was hoping to trade the bar to you for the 6' Homelite mount I need for the 2100 Super.....guess that's a "NO"?

I've known you to be a real good 'guesser' ....