Had a little surf and turf tonight. Venison backstrap from our property and walleye from Lake Erie. Yum! 
Scrounging Firewood (and other stuff)
- Thread starter mainewoods
- Start date
Help Support Arborist Forum:
MMG
ArboristSite Operative
Nope, just some bulk 55g PMC .233 SP so I can use for hunting. These rounds come around $0.49 if I recall. I feel better about shooting steel targets with it also. The stuff is rated at 3200 FPS so it's coming in pretty hot and holds out pretty flat.
I save my brass so maybe one day I will do some reloading.
The first tanneright was placed a but low so I got a longer stick and did it a second time.
I'm thinking maybe I should cut out a pocket about chest high, stick the tanneright in the pocket, then try. These Ash trees are getting scarry around here.
When I put the fireplace in in the 80s, the rack was one of those cheap ones. Burned through in a couple of years. Dad welded me one out of 1-1/4" rebar I had. It was heavy but it lasted for many years. It finally burned through so I'm making a new one. Didn't have enough of the large rebar so I switched to 2"x2" x1/4" angle iron.
The uprights are 3/4" rebar and the middle two are 8" long. Same height as my previous one. May shorten a little. I may weld some large nuts on the bottom side of the angle iron to act as feet. The vertical pipe on the left will be for a removeable "cooking hook" so I can use my new cast iron Dutch oven in the winter. At the points where the rebar deck meets the angle iron, the angle iron will be notched a little to make welding easier.
This is just dry fitted. Do you see anything I should be concerned about? Criticism welcomed.
The uprights are 3/4" rebar and the middle two are 8" long. Same height as my previous one. May shorten a little. I may weld some large nuts on the bottom side of the angle iron to act as feet. The vertical pipe on the left will be for a removeable "cooking hook" so I can use my new cast iron Dutch oven in the winter. At the points where the rebar deck meets the angle iron, the angle iron will be notched a little to make welding easier.
This is just dry fitted. Do you see anything I should be concerned about? Criticism welcomed.
MechanicMatt
Cut Split Stack Burn
Florida is too south for me
I am thinking, NC-Tennessee-Kentucky area.
Maybe Arkansas and Missouri too
I am thinking, NC-Tennessee-Kentucky area.
Maybe Arkansas and Missouri too
If you want to go, why wait? They have jobs down there as well.
@MechanicMatt
Start researching what states will tax your investments and pension if you have one when leaving PA.
I was talking to a good friend this weekend about the tax hit he’ll take to his FireFighters pension when he moves from PA and retires to Delaware…..
Start researching what states will tax your investments and pension if you have one when leaving PA.
I was talking to a good friend this weekend about the tax hit he’ll take to his FireFighters pension when he moves from PA and retires to Delaware…..
Taxes will be a lot cheaper than NY.
Might be tough to shovel ash out of there.
MechanicMatt
Cut Split Stack Burn
Family, the job I have now….
The pay is too much to walk away from. Easily paying for my kids college
But yeah, I scour Zillow Dailey daydreaming
I always felt that large spacing on the bottom allowed too many coals to fall through and into the ashes so they don't burn completely. More/tighter spacing or even an expanded metal screen on top may improve that. A thin screen would need to be replaced more often for sure. And feet tall enough to get the ash shovel under it as mentioned. If it's similar to what you had and you liked it, then go for it.
Don't be too sure, especially if you are retired. NYS does not tax any government pensions (I'm retired NYS), in addition excludes $20,000 of other pension income if you are older than 59 1/2 and does not tax Social Security.
Al lot of "lower tax States" do, and sometimes it depends on age, etc.
Good points you and @singinwoodwackr bring up. On my old one, I would lift it up with the poker to get the shovel underneath. So I think I will put feet on it so the angle is up off the bottom. I've rarely have the problem of incomplete burning; usually depends on the piece of wood. Plus, I have tried expanded metal, and little of the ash shifted through to the bottom. So, I'll keep the spacing the same. The old uprights in the back have long burned off. I see now that tall ones will prevent me from lifting the grate up in the front. They'll be shortened.
Made the first cuts today. This is white fir. 31" on one end, and 35.5" on the other end. I had to cut spots into the log to get the log dogs out of the way of the carriage. It's supposed to be able to handle a 36" log. It's so high up that I have to use a ladder to start and stop the engine. I'm new to this, and still figuring things out as I go.
Logging buddy came over last night helped burn off all those pine boards. Got them all done, but ended up only going in the house around 11:00. Which as irony has it, I woke up late for work this morning lol. I'll get some pictures tonight after work. They turned out pretty good.
I should have been more specific on the taxes. I was talking about property taxes. Take Missouri for instance. A customer of mine a few years ago was paying $900 a year for property taxes on his house and 40 acre parcel out in the country. At the same time I was paying $5500 for my house and 3 acres out in the country in Taxachusetts. Our farm next door is right up there with my house. Our woodlot across the street is under chapter 61a which saves us about 80% - 85% on taxes.
davidprivett
ArboristSite Member
- Joined
- Mar 7, 2014
- Messages
- 56
- Reaction score
- 69
just in case someone wants them I have 5 - .22 acre lots near crystal river fl. the wife inherated them we have no intrest in them as we are in Tn. and happy cell # 727 421 7072 leave text if interested,listed with remax now ,but will be coming off contract in next few months.
Plan ahead if you can afford it. Prices are always going up on property. I know someone that bought a large piece of property in NC about 10 years ago in anticipation of her retirement. Two years prior to retiring her and her husband built their dream house. She then sold her business/ house and moved South.
I looked into NC but they have a personal property tax . My old cars just to register them would be a huge amount it’s based on book value of the vehicle . And you pay the property tax every year . The road use tax is 3% when you first register but that’s a one time fee
Can't wait to see pics of your timecard Sean
.I managed to get the west wall in the shop all insulated and sheeted yesterday. I'll need to pull the bottom sheets back off to instal the green 2x6 that goes on the bottom, it's currently the floor joist for my "scaffolding", the deck on the trailer/the Christmas float lol.
Also bought a diablo metal blade yesterday so I can get the panels for the bay door cut. I still need to figure out exactly how I'll make the door articulate in and down when it is closed. Once I get the panels cut I'll mock the cutoffs up and see how my current idea works and go from there.
Next phase is another big day cleaning/organizing.
It's finished to the bottom now, but this is the last pic I took.
If I had a choice I'd move to the Dakotas, Montana or maybe Nebraska. I've been east and south and there's far too many people out there. Alas, it's not just up to me so we probably will end up in Alabama or the Florida panhandle. My wife wants to be close to the ocean/gulf in winter.
Similar threads
Want to Sell
4 free saws
